The battery smart unit detects the HV battery conditions (voltage, current, and temperature) and battery cooling fan voltage, and sends the detected signals to the power management control ECU via serial communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| U029A-123 | Lost Communication with Hybrid Battery Pack Sensor Module | Problem in serial communication between the battery smart unit and power management control ECU (1 trip detection) | ·
Wire harness or connector ·
Power management control ECU ·
Battery smart unit |
Comes on | Master Warning Light:
Comes on |
Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION
At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check for DTCs.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Only U029A-123 is output. | A |
| DTCs other than U029A-123 are also output. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear side seatback assembly LH.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
| *a | Component with harness connected
(Battery Smart Unit) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N18-3 (IGCT) - N18-6 (GND) | Power switch on (IG) | 11 to 14 V |
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
As there might be an intermittent malfunction in the battery smart unit power source circuit, inspect the following even if the measured voltage is as specified:
Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)
Fuse condition (before and after removing fuse(s)) (IGCT circuit)
Connection condition of connectors (IGCT circuit)
Wire harness condition (IGCT circuit)
Wire harness condition (GND circuit)
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the rear side seatback assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect connector I3 from the power management control ECU.
Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL
Remove the rear side seatback assembly LH.
Disconnect connector N18 from the battery smart unit.
Measure the resistance according to the value(s) in the table below.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
*b | Rear view of wire harness connector
(to Battery Smart Unit) |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-32 (BTH+) - N18-1 (BTH+) | Power switch off | Below 1 Ω |
| I3-33 (BTH-) - N18-4 (BTH-) | Power switch off | Below 1 Ω |
| N18-1 (BTH+) - N18-6 (GND) and Body ground | Power switch off | 10 kΩ or higher |
| N18-4 (BTH-) - N18-6 (GND) and Body ground | Power switch off | 10 kΩ or higher |
| *1 | No. 2 Engine Room Relay Block |
| *2 | PM IGCT Fuse |
Remove the PM IGCT fuse from the No. 2 engine room relay block.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | AM2 Fuse |
Remove the AM2 fuse from the engine room relay block and junction block assembly.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | ECU-IG2 NO. 1 fuse |
Remove the ECU-IG2 No. 1 fuse from the instrument panel junction block assembly.
Disconnect all connectors from the power management control ECU.
Measure the resistance according to the value(s) in the table below.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I3-32 (BTH+) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - A38-2 (+B2) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - A39-5 (+B1) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - A39-6 (MREL) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - I3-14 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-32 (BTH+) - A38-16 (GI) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - A38-2 (+B2) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - A39-5 (+B1) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - A39-6 (MREL) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - I3-14 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-33 (BTH-) - A38-16 (GI) | Power switch off | 10 kΩ or higher |
When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.
Connect the power management control ECU connectors.
Install the ECU-IG2 NO. 1 fuse to the instrument panel junction block assembly.
Install the AM2 fuse to the engine room relay block and junction block assembly.
Install the PM IGCT fuse to the No. 2 engine room relay block.
Connect the battery smart unit connector.
Install the rear side seatback assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the rear side seatback assembly LH.
Disconnect connector N18 from the battery smart unit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
| *a | Rear view of wire harness connector
(to Battery Smart Unit) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N18-1 (BTH+) - N18-6 (GND) | Power switch on (IG) | 2.3 to 2.7 V |
| N18-4 (BTH-) - N18-6 (GND) | Power switch on (IG) | 2.3 to 2.7 V |
Turning the power switch on (IG) with the battery smart unit connector and power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *a | Rear view of wire harness connector
(to Battery Smart Unit) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N18-1 (BTH+) - N18-4 (BTH-) | Power switch off | 4.4 to 5.4 kΩ |
Resistance becomes 2.0 kΩ or less when there is a short circuit in the power management control ECU.
Connect the battery smart unit connector.
Install the rear side seatback assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG