Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074886 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AAE-123  Hybrid Battery Pack Air Temperature Sensor "A" Circuit Low  P0AAF-123  Hybrid Battery Pack Air Temperature Sensor "A" Circuit High  


DESCRIPTION

The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensor (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123). The battery smart unit uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.


HINT:

After confirming that DTC P0AAE-123 or P0AAF-123 is output, use the intelligent tester to check "Inhaling Air Temp" in the HV ECU data list.


Displayed Temperature Malfunction
-45 °C (-49 °F) or less Open or +B short circuit
95 °C (203 °F) or more GND short

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AAE-123 Hybrid Battery Pack Air Temperature Sensor "A" Circuit Low When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open circuit) or is higher than a predetermined limit (short circuit)
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on
P0AAF-123 Hybrid Battery Pack Air Temperature Sensor "A" Circuit High When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open circuit) or is higher than a predetermined limit (short circuit)
·

HV battery

·

Battery smart unit

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A9C-123.

See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A9C-123

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK FOR DTCS (HV)

A

2.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR

B

2.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Check installation of inlet air temperature sensor.

i.
A260253E02
0.167,0.927 0.51,1.208 0.344,0.281 0.281,0.948 0.49,1.198 0.208,0.25 10 true z8

Check the connections of the z8 connector of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.


Result:
Result Proceed to
NG B
OK Go to next step



ii.
A244312

Visually check the installation condition of the inlet air temperature sensor.

OK:

The inlet air temperature sensor is installed in the correct location and its claws are engaged securely.


Result:
Result Proceed to
The inlet air temperature sensor is installed in the correct location and its claws are engaged securely A
Claws are damaged. C
Inlet air temperature sensor is not installed correctly, but claws are not damaged. D




d.

Install the luggage compartment front trim cover.



A

3.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

D

INSTALL PARTS CORRECTLY

3.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Remove the rear side seat back assembly LH.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


d.

Disconnect connectors N18 and z8 from the battery smart unit.


e.
A244309C10
0.813,1.573 1.24,1.833 0.427,0.26 0.531,3.385 0.958,3.646 0.427,0.26 1.531,2.292 1.104,2.229 true 2.052,4.396 1.906,4.146 true 2.552,3.563 1.917,3.979 true 2.438,3.26 1.792,3.99 true 1.031,3.969 1.635,4 true 1.042,4.281 1.635,4.104 true 1.396,4.396 1.792,4.115 true 2.521,3.875 2.021,4.01 true 2.552,4.125 2.031,4.094 false 1.531,2.469 1.104,2.604 true 0.177,0.125 0.448,0.302 0.271,0.177 10 false *a 0.781,2.125 1.177,2.365 0.396,0.24 10 false IGCT 0.719,3.885 1.063,4.094 0.344,0.208 10 false TBO 2.448,3.135 2.781,3.344 0.333,0.208 10 false TB1 2.573,3.417 2.875,3.625 0.302,0.208 10 false TB2 0.677,4.208 1.031,4.406 0.354,0.198 10 false GBO 1.156,4.427 1.49,4.615 0.333,0.188 10 false GB1 2.021,4.417 2.427,4.615 0.406,0.198 10 false GB2 2.583,3.75 2.958,3.938 0.375,0.188 10 false TCO 2.594,4.042 2.969,4.25 0.375,0.208 10 false GCO 0.875,1.625 1.177,1.771 0.302,0.146 10 false N18 0.646,3.438 0.875,3.583 0.229,0.146 10 false z8 0.781,2.542 1.177,2.781 0.396,0.24 10 false GND
*a Rear view of wire harness connector
(to Battery Smart Unit)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z8-1 (TCO) - z8-7 (GCO) 0 °C (32 °F) 26.7 to 27.8 kΩ
25 °C (77 °F) 9.9 to 10.1 kΩ
40 °C (104 °F) 5.73 to 5.92 kΩ



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z8-1 (TCO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-1 (TCO) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-7 (GCO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-7 (GCO) - N18-6 (GND) Power switch off 10 kΩ or higher



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
z8-4 (TBO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-4 (TBO) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-10 (GBO) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-10 (GBO) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-3 (TB1) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-3 (TB1) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-9 (GB1) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-9 (GB1) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-2 (TB2) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-2 (TB2) - N18-6 (GND) Power switch off 10 kΩ or higher
z8-8 (GB2) - N18-3 (IGCT) Power switch off 10 kΩ or higher
z8-8 (GB2) - N18-6 (GND) Power switch off 10 kΩ or higher



h.

Connect the battery smart unit connectors.


i.

Install the rear side seat back assembly LH.


j.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the luggage compartment front trim cover.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE DOOR HINGE TORSION BAR>REMOVAL


c.

Check the wire harness and connectors of the battery temperature sensor and inlet air temperature sensor for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.



HINT:

Because the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery assembly.


d.

Install the luggage compartment front trim cover.


Result:
Proceed to
OK
NG



OK

NG

REPAIR HARNESS OR CONNECTOR