Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074900 ENGINE G

2AR-FXE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner cap.


b.

Remove the air cleaner filter element.


c.

Visually check that the air cleaner filter element is not excessively damaged or oily.

If necessary, replace the air cleaner filter element.


d.

Install the air cleaner filter element.


e.

Install the air cleaner cap.


Hide 5.INSPECT VALVE AND ADJUSTER NOISE

a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Rev up the engine several times. Check that the engine does not emit unusual noises. If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then, perform the inspection above again. If any defects or problems are found during the inspection above, perform a lash adjuster inspection.

Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


Hide 6.INSPECT IGNITION TIMING

a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Warm up and stop the engine.


c.

When using the intelligent tester:

Check the ignition timing.

i.

Connect the intelligent tester to the DLC3.


ii.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:

5 to 20 degrees BTDC


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the shift lever should be in P.



HINT:

Refer to the intelligent tester operator's manual for further details.



iv.

Check that the ignition timing advances immediately when the engine speed is increased.


v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vi.

Monitor IGN Advance of the Data List.

Standard ignition timing:

8 to 12 degrees BTDC


NOTICE:

When checking the ignition timing, the shift lever should be in P.


HINT:

Refer to the intelligent tester operator's manual for further details.



vii.

Enter the following menus: Connect the TC and TE1 / OFF.


viii.

Turn the power switch off.


ix.

Turn the intelligent tester off.


x.

Disconnect the intelligent tester from the DLC3.



d.

When not using the intelligent tester:

i.
A122830C26
1.094,0.604 1.552,1.063 false 1.76,1.656 1.375,2.042 false 0.927,1.063 1.042,1.219 0.115,0.156 10 1 0.927,1.469 1.042,1.625 0.115,0.156 10 9 1.104,1.469 1.281,1.625 0.177,0.156 10 10 1.302,1.469 1.479,1.625 0.177,0.156 10 11 1.51,1.469 1.688,1.625 0.177,0.156 10 12 1.719,1.469 1.896,1.625 0.177,0.156 10 13 1.927,1.469 2.104,1.625 0.177,0.156 10 14 2.125,1.469 2.302,1.625 0.177,0.156 10 15 2.333,1.469 2.51,1.625 0.177,0.156 10 16 1.135,1.063 1.25,1.219 0.115,0.156 10 2 1.344,1.063 1.458,1.219 0.115,0.156 10 3 1.552,1.063 1.667,1.219 0.115,0.156 10 4 1.75,1.063 1.865,1.219 0.115,0.156 10 5 1.958,1.063 2.073,1.219 0.115,0.156 10 6 2.156,1.063 2.271,1.219 0.115,0.156 10 7 2.365,1.063 2.479,1.219 0.115,0.156 10 8 0.792,0.5 1.042,0.656 0.25,0.156 10 CG 1.594,0.156 1.76,0.333 0.167,0.177 10 *1 1.115,1.958 1.365,2.104 0.25,0.146 10 TC
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminals before connecting them. Connecting the wrong terminals may result in damage to electrical components.

·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the shift lever should be in P.




ii.

Remove the No. 1 engine cover sub-assembly.


iii.

Pull out the wire harness.

NOTICE:

After checking, wrap the wire harness with tape.



iv.
A259770

Connect the clip of the timing light to the wire harness.

NOTICE:

Use a timing light that detects the primary signal.



v.

Inspect the ignition timing at idle.

Standard ignition timing:

8 to 12 degrees BTDC


NOTICE:

When checking the ignition timing, the shift lever should be in P.


HINT:

After running the engine at 1000 to 1300 rpm for 5 seconds, check that it returns to idle speed.



vi.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


vii.

Inspect the ignition timing at idle.

Standard ignition timing:

5 to 20 degrees BTDC



viii.

Confirm that the ignition timing advances when the engine rpm is increased.


ix.

Remove the timing light.


x.

Install the No. 1 engine cover sub-assembly.



Hide 7.INSPECT ENGINE IDLE SPEED

a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Warm up and stop the engine.


c.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.


ii.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

HINT:

Refer to the intelligent tester operator's manual for further details.


Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

iv.

Inspect the engine idle speed.

Standard idle speed:

900 to 1050 rpm


NOTICE:
·

Turn all electrical systems and the A/C off.

·

Inspect the idle speed with the cooling fans off.

·

When checking the ignition timing, the shift lever should be in P.




v.

Turn the power switch off.


vi.

Turn the intelligent tester off.


vii.

Disconnect the intelligent tester from the DLC3.



d.

When not using the intelligent tester:

i.
A122830C25
0.823,1.958 0.969,1.667 false 0.927,1.063 1.042,1.219 0.115,0.156 10 false 1 0.927,1.469 1.042,1.625 0.115,0.156 10 false 9 1.104,1.469 1.281,1.625 0.177,0.156 10 false 10 1.302,1.469 1.479,1.625 0.177,0.156 10 false 11 1.51,1.469 1.688,1.625 0.177,0.156 10 false 12 1.719,1.469 1.896,1.625 0.177,0.156 10 false 13 1.927,1.469 2.104,1.625 0.177,0.156 10 false 14 2.125,1.469 2.302,1.625 0.177,0.156 10 false 15 2.333,1.469 2.51,1.625 0.177,0.156 10 false 16 1.135,1.063 1.25,1.219 0.115,0.156 10 false 2 1.344,1.063 1.458,1.219 0.115,0.156 10 false 3 1.552,1.063 1.667,1.219 0.115,0.156 10 false 4 1.75,1.063 1.865,1.219 0.115,0.156 10 false 5 1.958,1.063 2.073,1.219 0.115,0.156 10 false 6 2.156,1.063 2.271,1.219 0.115,0.156 10 false 7 2.365,1.063 2.479,1.219 0.115,0.156 10 false 8 1.594,0.156 1.948,0.396 0.354,0.24 10 false *1 0.688,2 1.083,2.177 0.396,0.177 10 false TAC
*1 DLC3


Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  


ii.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


iii.

Inspect the engine idle speed.

Standard idle speed:

900 to 1050 rpm


NOTICE:
·

Turn all electrical systems and the A/C off.

·

Inspect the idle speed with the cooling fans off.

·

When checking the ignition timing, the shift lever should be in P.




iv.

Disconnect the tachometer probe from the DLC3.



Hide 8.INSPECT COMPRESSION

a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Warm up and stop the engine.


c.

Remove the 4 spark plugs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL

NOTICE:

If the ignition coil assembly connector is disconnected because a DTC is detected in inspection, always reconnect it.



d.
A259769

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Connect the intelligent tester to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Turn the intelligent tester on.

NOTICE:

Check the HV battery voltage in the data list to ensure that the battery is fully charged.



v.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Compression Test / ON.

Powertrain > Hybrid Control > Active Test
Tester Display
Compression Test
50004 236 5

vi.

Depress and hold the brake pedal, and turn the power switch on (READY).

NOTICE:

The measurement must be done as quickly as possible.


HINT:

Noise may be emitted from the transmission. However, this is not a malfunction.


Standard compression pressure:

1100 kPa (11.2 kgf/cm2, 160 psi)


Minimum pressure:

750 kPa (7.6kgf/cm2, 109 psi)


Pressure difference between each cylinder:

100 kPa (1.0 kgf/cm2, 15 psi)


NOTICE:
·

Inspect the other cylinders in the same way.

·

Measure the compression as quickly as possible.




vii.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, then inspect it again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, a valve may be stuck or seated improperly, or there may be leaks from the gasket.





e.

Install the 4 spark plugs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:

After performing all the steps, be sure to clear any DTCs stored in memory.



Hide 9.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO / HC complies with regulations.


a.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Warm up the engine.


c.

Run the engine at 2500 rpm for approximately 180 seconds.


d.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.


e.

Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.

HINT:

When doing a 2 mode (with the engine idling/ running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.



ii.

See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Possible Cause
Normal High Rough idle
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaks from intake and exhaust valves

4.

Leaks from cylinders

5.

Faulty EGR


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body


2.

Lean mixture causing misfire

3.

Faulty EGR


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element

2.

Plugged PCV valve

3.

Faulty EFI systems:

·

Faulty pressure regulator

·

Faulty engine coolant temperature sensor

·

Faulty mass air flow meter

·

Faulty ECM

·

Faulty injectors

·

Throttle body


4.

Faulty EGR