Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074904 REAR CRANKSHAFT OIL SEAL A

2AR-FXE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




b.
A195810
1.292,1.354 1.99,1.927 true 2,1.927 1.854,1.188 true 2.073,1.875 2.479,2.052 0.406,0.177 10 SST

Using SST and a hammer, tap in the oil seal until its surface is flush with the edges of the cylinder block and crankcase.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Keep the lip of the oil seal free from foreign matter.

·

Do not tap in the oil seal at an angle.




Hide 13405 2.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A195875
1.375,1.26 0.854,1.26 false 1.292,0.781 1.146,0.781 1.146,0.781 1.146,1.26 false 0.49,1.177 0.823,1.333 0.333,0.156 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



b.
A192239
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
A259955
2.552,1.073 2.646,1.229 0.094,0.156 10 true 3 1.844,0.365 1.958,0.521 0.115,0.156 10 true 8 1.865,1.76 1.958,1.917 0.094,0.156 10 true 7 2.385,1.573 2.479,1.729 0.094,0.156 10 true 5 1.354,1.573 1.448,1.729 0.094,0.156 10 true 2 1.177,1.073 1.271,1.229 0.094,0.156 10 true 4 2.375,0.552 2.469,0.708 0.094,0.156 10 true 1 1.354,0.552 1.448,0.708 0.094,0.156 10 true 6

Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the flywheel sub-assembly.



d.

Check that the crankshaft turns smoothly.


Hide 31270 3.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.
A195875
1.375,1.26 0.854,1.26 false 1.292,0.781 1.146,0.781 1.146,0.781 1.146,1.26 false 0.49,1.177 0.823,1.333 0.333,0.156 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



b.

Install the transmission input damper assembly.


c.
A260502
1.375,0 1.469,0.156 0.094,0.156 10 true 1 2.917,0.427 3.01,0.583 0.094,0.156 10 false 6 2.844,1.656 2.938,1.813 0.094,0.156 10 false 4 0.583,0.385 0.677,0.542 0.094,0.156 10 true 3 0.656,1.594 0.75,1.75 0.094,0.156 10 false 5 1.323,1.979 1.417,2.135 0.094,0.156 10 false 2

Install and uniformly tighten the 6 bolts in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Take care not to insert the transmission input damper assembly in the wrong direction.




Hide 30900 4.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY