Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › HYBRID VEHICLE TRANSAXLE
RM2040EQ _52 Drivetrain _014701 P314 HYBRID TRANSMISSION / TRANSAXLE _0074944 HYBRID VEHICLE TRANSAXLE A

P314 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL WITH HEAD STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the with head straight screw plug is necessary.


a.

Coat a new O-ring with ATF and install them to the with head straight screw plug.


b.

Using a 10 mm hexagon socket wrench, install the with head straight screw plug to the hybrid vehicle transaxle assembly.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide G90A0A 2.INSTALL NO. 1 INVERTER COOLING HOSE ASSEMBLY

a.

Install the No. 1 inverter cooling hose assembly to the hybrid vehicle transaxle assembly.


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 2 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 39195 4.INSTALL HYBRID TRANSAXLE MASS DAMPER

a.

Install a new gasket and the hybrid transaxle mass damper.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 35153C 5.INSTALL NO. 3 AUTOMATIC TRANSMISSION CASE COVER

a.

Install the No. 3 automatic transmission case cover to the hybrid vehicle transaxle assembly with the 2 bolts and a new clip.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 35151J 6.INSTALL AUTOMATIC TRANSMISSION CASE COVER

a.

Engage the 2 guides and install the automatic transmission case cover.


Hide 33827 7.INSTALL NO. 3 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 3 transmission control cable bracket to the hybrid vehicle transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33826A 8.INSTALL NO. 2 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 2 transmission control cable bracket to the hybrid vehicle transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33823 9.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12311A 10.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 30900 11.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

a.
C244781
1.146,1.146 2.948,1.146 true 2.271,0.406 2.271,1.135 true 2.979,1.063 3.167,1.229 0.188,0.167 10 false *1 1.313,2.365 1.5,2.531 0.188,0.167 10 false A 2.146,2.198 2.333,2.365 0.188,0.167 10 false A 2.802,2.813 2.99,2.979 0.188,0.167 10 true B 2.958,3.438 3.146,3.604 0.188,0.167 10 false C 2.792,4.01 2.979,4.177 0.188,0.167 10 false D 1.021,4.115 1.156,4.302 0.135,0.188 10 true D 1.448,4.396 1.635,4.563 0.188,0.167 10 false D 2.573,4.25 2.76,4.417 0.188,0.167 10 false D 0.833,2.917 0.979,3.115 0.146,0.198 10 true E
*1 Knock Pin


Make sure that the knock pins are installed to the engine.


b.

Install the hybrid vehicle transaxle assembly to the engine with the 9 bolts.

Bolt Bolt Length Torque
A, B 55 mm (2.17 in.) 64 N*m (653 kgf*cm, 47 ft.*lbf)
C 65 mm (2.56 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
D 32 mm (1.26 in.) 44 N*m (449 kgf*cm, 32 ft.*lbf)
E 38 mm (1.50 in.) 28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:
·

Do not apply grease either to the spline or to the input shaft.

·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the hybrid vehicle transaxle assembly.

·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.

·

When inserting the input shaft of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the hybrid vehicle transaxle assembly excessively.

·

When mounting the hybrid vehicle transaxle assembly to the engine, make sure to securely fit the knock pins into the knock holes.



HINT:

Temporarily tighten bolt B first.



Hide 13.CONNECT WIRE HARNESS

a.

Connect the 3 clamps and install the motor cable to the hybrid vehicle transaxle assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
C243593
1.823,3.479 2.01,3.656 0.188,0.177 10 true A 1.771,1.979 1.917,2.167 0.146,0.188 10 true A 2.583,2.635 2.729,2.792 0.146,0.156 10 false B

Connect the 3 clamps, 4 connectors and install the wire harness to the hybrid vehicle transaxle assembly with the 3 bolts.

Torque:
Bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

Torque:
Bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 14.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE