Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014694 2AR-FXE FUEL _0074909 FUEL SYSTEM G

2AR-FXE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the power switch on (IG) and turn the intelligent tester on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

iv.

Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the power switch off.


d.

Disconnect the intelligent tester from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL SYSTEM>PRECAUTION


b.

Using a voltmeter, measure the auxiliary battery voltage.

Standard voltage:

11 to 14 V



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Disconnect the fuel hose from the fuel main tube.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL SYSTEM>PRECAUTION


e.
A264978C08
0.854,0.49 0.604,0.49 false 1.51,0.771 1.51,1.073 false 1.115,0.969 1.115,1.156 false 2.885,0.406 2.656,0.177 2.656,0.177 2.531,0.177 false 2.01,1.646 2.313,1.354 2.313,1.354 2.385,1.354 false 0.792,2.365 0.792,2.563 false 2.198,2.333 2.198,2.479 false 3.26,2.635 3.021,2.635 false 1.583,3.344 1.833,3.083 1.833,3.083 1.917,3.083 false 2.333,3.573 2.583,3.823 2.583,3.823 2.656,3.823 false 1.375,3.938 1.51,4.073 1.51,4.073 1.604,4.073 false 0.406,0.396 0.563,0.552 0.156,0.156 10 false *1 1.438,1.104 1.594,1.26 0.156,0.156 10 false *1 1.042,1.177 1.198,1.333 0.156,0.156 10 false *2 2.323,0.083 2.479,0.24 0.156,0.156 10 false *3 2.438,1.271 2.594,1.427 0.156,0.156 10 false *4 2.125,2.51 2.281,2.667 0.156,0.156 10 false *4 0.698,2.594 0.854,2.75 0.156,0.156 10 false *6 2.833,2.552 2.99,2.708 0.156,0.156 10 false *7 2.667,3.729 2.823,3.885 0.156,0.156 10 false *5 1.938,2.979 2.094,3.135 0.156,0.156 10 false *1 1.625,3.99 1.781,4.146 0.156,0.156 10 false *4
*1 SST
(Hose Band)
*2 SST
(T-joint)
*3 SST
(Pressure Gauge)
*4 SST
(Hose)
*5 SST
(Fuel Tube Connector)
*6 Fuel Tube
*7 Fuel Pipe


Install SST (pressure gauge) using other SST and a fuel tube connector as shown in the illustration.

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)
09268-45014  (09268-41200, 09268-41220, 09268-41250)


f.

Wipe up any spilled gasoline.


g.

Connect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



h.

Connect the intelligent tester to the DLC3.


i.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

j.

Measure the fuel pressure.

Standard fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


·

If the fuel pressure is greater than the standard value, replace the fuel pressure regulator.

·

If the fuel pressure is less than the standard value, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.



k.

Disconnect the intelligent tester from the DLC3.


l.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


m.

Start the engine.


n.

Measure the fuel pressure at idle.

Standard fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)



o.

Stop the engine.


p.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or more


If the fuel pressure is not as specified, check the fuel pump, pressure regulator and/or fuel injectors.


q.

After checking the fuel pressure, disconnect the cable from the negative (-) auxiliary battery terminal and carefully remove SST to prevent gasoline from splashing.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



r.

Reconnect the fuel tube to the main fuel tube (fuel tube connector).


s.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


t.

Inspect for fuel leaks (See step 1).

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.