Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL SYSTEM
RM2040EQ _51 Engine / Hybrid System _014694 2AR-FXE FUEL _0074909 FUEL SYSTEM L

2AR-FXE FUEL  FUEL SYSTEM  PRECAUTION  


BEFORE WORKING ON FUEL SYSTEM


a.

When disconnecting a fuel line, fuel will splash. So observe the following precautions:

i.

Do not smoke or work near fire when handling the fuel system.


ii.

Keep gasoline away from rubber or leather parts.


iii.

Perform the Discharge Fuel System Pressure procedure below before disconnecting a fuel line to prevent gasoline from spilling out.




DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Perform the following procedure to prevent fuel from spilling out before removing any fuel system parts.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a shop rag or a piece of cloth to prevent fuel from spraying or coming out.



a.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


b.

Remove the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.
A218217

Remove the rear floor service hole cover.


d.

Disconnect the fuel pump connector.


e.

Put the engine in inspection mode.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


f.

Start the engine.


g.

After the engine has stopped on its own, turn the power switch off.


h.

Crank the engine again and make sure that the engine does not start.

HINT:

Some DTCs may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



j.

Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.


k.

Connect the fuel pump connector.


l.

Install the rear floor service hole cover with new butyl tape.


m.

Install a new rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION


n.

Install the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION



FUEL LINE


a.

When disconnecting a high pressure fuel line, a large amount of gasoline will spill out, so perform the following procedure:

i.

Discharge fuel system pressure (See step 2).


ii.

Disconnect the fuel pump tube.


iii.

Drain the fuel that remains in the fuel pump tube.


iv.

Cover the disconnected fuel pump tube with a plastic bag to prevent damage and contamination.


v.

Put a container under the connectors.



b.
A259297C02
0.677,3.938 0.677,4.125 false 1.885,4.292 1.938,4.344 1.938,4.344 2.042,4.344 false 1.458,1.51 0.99,0.438 0.99,0.438 0.875,0.438 false 1.76,3.802 2.094,3.802 false 2.646,0.469 2.844,0.677 0.198,0.208 10 false *2 0.667,0.365 0.865,0.573 0.198,0.208 10 false *1 0.563,4.146 0.948,4.313 0.385,0.167 10 false SST 2.073,4.25 2.458,4.427 0.385,0.177 10 false SST 2.177,3.729 2.375,3.938 0.198,0.208 10 false *3
*1 No. 2 Fuel Pipe Clamp
*2 Retainer
*3 Fuel Tube Connector
V100135

Turn
V100136

Pull


Perform the following procedure when disconnecting the fuel tube.

NOTICE:

Do not forcibly bend, kink or twist the fuel tube.


i.

Remove the No. 2 fuel pipe clamp.


ii.

Wipe off any dirt on the fuel tube connector.


iii.

Hold the fuel tube connector, and then install SST.

SST
09268-21011  


iv.

Turn SST to align the retainer inside the fuel tube connector with the chamfered part of SST.


v.

Insert SST into the fuel tube connector and hold it. Then push the fuel tube connector toward SST.


vi.

Mount the retainer of the fuel tube connector onto the chamfered part of SST.


vii.
A158904C09
0.479,1.052 0.479,1.25 false 1.292,1.063 1.385,1.26 1.385,1.26 1.49,1.073 false 2.135,0.521 1.552,0.229 false 3,1.01 3,1.26 false 2.26,1.24 2.26,1.542 false 1.302,1.281 1.479,1.448 0.177,0.167 10 false *2 1.354,0.167 1.635,0.385 0.281,0.219 10 false *1 2.927,1.26 3.115,1.438 0.188,0.177 10 false *5 2.167,1.563 2.385,1.719 0.219,0.156 10 false *4 0.406,1.292 0.615,1.469 0.208,0.177 10 false *3
*1 Retainer
*2 O-ring
*3 Fuel Tube
*4 Fuel Tube Connector
*5 Fuel Pipe


Slide SST and the fuel tube connector together toward the fuel tube until they make a "click" sound, and then disconnect the fuel tube.


viii.

Drain the fuel remaining inside the fuel tube.


ix.

Cover the fuel tube and fuel pipe with plastic bags to protect the disconnected part.



c.
A259298C02
1.414,1.059 2.234,0.238 2.234,0.238 2.391,0.238 false 2.471,0.149 2.675,0.385 0.204,0.236 10 *1
*1 No. 2 Fuel Pipe Clamp
V100135

Push


Perform the following procedure when connecting the fuel tube.

i.

Check if there is any damage or foreign objects on the connecting part of the fuel pipe.


ii.

Match the axis of the fuel tube connector with the axis of the fuel pipe, and push it into the fuel tube connector until the fuel tube connector makes a "click" sound. If the connection is tight, apply a small amount of clean engine oil to the tip of the fuel pipe.


iii.
A304570C01
1.958,0.771 2.115,0.969 0.156,0.198 10 false .
V100135

Push
V100136

Pull


After finishing the connection, check if the fuel pipe and the fuel tube connector are securely connected by pulling on them.


iv.

Inspect for fuel leaks.


v.

Install a new No. 2 fuel pipe clamp.



d.

Perform the following procedure when disconnecting the fuel tube connector (quick type A):

i.
A207802

Remove the fuel pipe clamp.


ii.

Check whether there is any dirt on the fuel pipe around the fuel tube connector before disconnecting it and remove the dirt as necessary.


iii.
A159424C22
2.5,1.271 2.729,1.198 2.729,1.198 2.563,1.49 false 2.177,3.719 2.177,4.042 2.177,4.042 1.729,4.042 false 2,3.719 2,4.042 false 2.552,3.344 2.271,3.063 2.271,3.063 2.167,3.063 false 2.667,3.896 2.833,4.052 2.833,4.052 2.927,4.052 false 2.781,1.083 2.969,1.271 0.188,0.188 10 false *1 1.99,2.979 2.188,3.198 0.198,0.219 10 false *1 1.552,3.958 1.729,4.188 0.177,0.229 10 false *2 2.958,3.979 3.156,4.198 0.198,0.219 10 false *3
*1 Retainer
*2 O-ring
*3 Fuel Tube Connector
V100135

Pinch
V100136

Pull Out


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iv.

If the fuel tube connector and the fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector out of the fuel pipe carefully.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



v.

Check that there is no dirt or other foreign matter on the sealing surfaces of the disconnected fuel pipes. Clean the surfaces if necessary.


vi.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.
A121423

Perform the following procedure when connecting a fuel tube connector (quick type A):

i.

Check if there is any damage or foreign objects on the connecting parts of the fuel pipes.


ii.

Line up the 2 parts of the fuel pipes to be connected, and push them together until the fuel tube connector makes a "click" sound. If the fuel pipe is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


iii.

After connecting the fuel pipes, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



v.

Install the No. 1 fuel pipe clamp.



f.
A283943C07
0.865,0.542 1.135,0.167 1.135,0.167 1.302,0.167 false 0.25,0.438 0.354,0.167 0.354,0.167 0.458,0.167 false 0.438,1.24 0.583,0.802 false 1.375,0.115 1.688,0.271 0.313,0.156 10 false *2 0.51,0.094 0.823,0.25 0.313,0.156 10 false *1 0.333,1.271 0.646,1.427 0.313,0.156 10 false *3
*1 Fuel Tube Connector
*2 Fuel Pipe
*3 Retainer
V100135

Pinch
V100136

Pull Out


Perform the following procedure when disconnecting a fuel tube connector (quick type B):

i.

Check that there is no dirt or other foreign matter around the fuel tube connector before disconnecting it. Clean the joint if necessary.


ii.

Pinch the retainer as shown in the illustration, then pull out the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iii.
A283944

If the fuel tube connector and fuel pipe are stuck, pinch the fuel pipe, then push and pull the fuel tube connector to release and disconnect the fuel tube connector.


iv.

Check if there is any dirt or other foreign matter on the sealing surface of the disconnected fuel pipe and clean it away as necessary.


v.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.
A283945

Perform the following procedure when connecting a fuel tube connector (quick type B):

i.

Check for damage or foreign matter on the connecting part of the fuel pipe.


ii.

Align the fuel tube connector with the fuel pipe, then push in the fuel tube connector until the retainer makes a "click" sound.

HINT:

If the fuel pipe is difficult to push into the fuel tube connector, apply a light coat of engine oil to the tip of the fuel pipe and reinsert it.



iii.
A283946

After finishing the connection, check that the fuel pipe and the fuel tube connector are securely connected by pulling on them.




h.

Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the fuel tube connector part of the nylon tube or the fuel tube connector when connecting them.

·

Do not remove the EPDM protector on the outside of the nylon tube.

·

Do not pinch or kink the nylon tubes to prevent fuel leakage.





INJECTOR


a.
A217166C06
2.393,0.295 1.914,0.112 1.914,0.112 1.433,0.112 false 2.502,0.701 2.966,0.959 false 1.122,1.523 0.688,1.089 0.688,1.089 0.475,1.089 false 0.198,1.014 0.381,1.233 0.183,0.219 10 *3 1.197,0.026 1.379,0.274 0.183,0.249 10 *1 3.018,0.906 3.207,1.214 0.19,0.308 10 *2
*1 Delivery Pipe
*2 O-ring
*3 Insulator


Install the injector to the delivery pipe and cylinder head as shown in the illustration.

NOTICE:

Before installing the injector, be sure to apply a light coat of gasoline or spindle oil where the delivery pipe contacts the injector O-ring.



b.
A222009C04
0.159,0.131 3.222,1.397 3.063,1.265 0.159,1.464 3.222,3.214 3.063,1.75 0.224,0.191 0.418,0.45 0.194,0.258 10 *a 0.212,1.523 0.406,1.782 0.194,0.258 10 *b 0.676,1.17 0.87,1.428 0.194,0.258 10 *1 1.138,1.17 1.332,1.428 0.194,0.258 10 *2 0.76,0.907 0.76,1.17 false 1.216,1.06 1.216,1.17 false 0.66,2.707 0.854,2.966 0.194,0.258 10 *1 1.122,2.707 1.316,2.966 0.194,0.258 10 *2 0.744,2.376 0.744,2.707 false 1.2,2.545 1.2,2.707 false
*1 O-ring
*2 Delivery Pipe
*a CORRECT
*b INCORRECT


Observe the following precautions when removing and installing the fuel injectors:

i.

Do not reuse the O-ring and insulator.


ii.

When placing a new O-ring on the injector, do not damage the O-ring.


iii.

Coat a new O-ring with spindle oil or gasoline before installing it.

NOTICE:

Do not use engine oil, gear oil or brake fluid.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


a.
A261665C02
0.529,0.728 0.707,0.906 0.178,0.178 10 *1 1.166,1.12 0.858,0.813 0.858,0.813 0.725,0.813 false
*1 Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is welded to the plate.



INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION