Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL INJECTOR
RM2040EQ _51 Engine / Hybrid System _014694 2AR-FXE FUEL _0074910 FUEL INJECTOR G

2AR-FXE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.



b.

Inspect the injector injection volume.

CAUTION:

Keep the injector away from sparks during the test.


i.
A264971
0.531,1.656 0.76,1.885 0.76,1.885 0.865,1.885 false 0.854,0.906 1.146,0.615 1.146,0.615 1.26,0.615 false 1.99,1.281 2.292,1.583 2.292,1.583 2.417,1.583 false 2.615,0.719 2.917,0.417 2.917,0.417 3.031,0.417 false 0.885,1.792 1.063,1.969 0.177,0.177 10 false *1 1.302,0.542 1.531,0.781 0.229,0.24 10 false *2 2.448,1.51 2.625,1.688 0.177,0.177 10 false *3 3.094,0.344 3.271,0.521 0.177,0.177 10 false *4
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Fuel Tube Connector)
*4 Fuel Pipe (Vehicle Side)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)


ii.
A264972
1.344,0.094 0.969,0.094 false 1.74,0.344 2.031,0.344 false 1.302,0.76 0.969,0.76 false 1.49,1.021 1.656,1.021 false 2.094,1.365 2.438,1.365 false 1.323,1.896 0.979,1.896 false 0.771,0 0.938,0.177 0.167,0.177 10 *1 2.094,0.208 2.26,0.385 0.167,0.177 10 *2 0.792,0.656 0.958,0.833 0.167,0.177 10 *3 1.698,0.938 1.865,1.115 0.167,0.177 10 *4 2.5,1.292 2.667,1.469 0.167,0.177 10 *5 0.802,1.823 0.969,2 0.167,0.177 10 *6
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Adapter)
*4 O-ring
*5 SST
(Clamp)
*6 Vinyl Tube


Install a new O-ring to the fuel injector.

SST
09268-31014  (09268-41110, 09268-41300, 09268-41700, 95336-08070)


iii.

Connect SST (adapter and hose) to the injector, and hold the injector and union with SST (clamp).


iv.

Install a vinyl tube onto the injector.

CAUTION:

Install a suitable vinyl tube onto the injector to contain any gasoline spray.



v.
A264974
1.938,0.417 2.469,0.417 false 2.135,1.406 2.5,1.406 false 1.229,0.354 0.74,0.354 false 0.563,0.281 0.75,0.458 0.188,0.177 10 *1 2.552,0.333 2.74,0.51 0.188,0.177 10 *2 2.563,1.323 2.75,1.5 0.188,0.177 10 *3
*1 SST
(Tie Band)
*2 SST
(Adapter)
*3 SST
(Clamp)


Tie the clamp and adapter together with a tie band as shown in the illustration.

SST
09268-31014  (09268-41110, 09268-41300, 09268-41800)


vi.

Put the injector into the graduated cylinder.



viii.
A264973
2.021,0.552 2.021,0.969 false 1.958,1.01 2.115,1.25 0.156,0.24 10 *1 1.021,1.333 1.177,1.573 0.156,0.24 10 *a
*1 SST
(Wire)
*a Connect


Connect SST (wire) to the injector and the auxiliary battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

NOTICE:

Always switch the voltage on and off at the auxiliary battery side, not the injector side.


Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive terminal - Ground terminal Per 15 seconds 87 to 105 cc (5.3 to 6.4 cu.in.)


Difference between each injector:

18 cc (1.1 cu.in.) or less


If the result is not as specified, replace the fuel injector assembly.



c.

Check for fuel drop.

i.

In the condition above, disconnect the tester probes of SST (wire) from the auxiliary battery and check for fuel drop from the injector.

Standard fuel drop:

1 drop or less per 20 minutes


If fuel drop is not as specified, replace the fuel injector assembly.