Home › Engine / Hybrid System › 2AR-FXE INTAKE / EXHAUST › EXHAUST PIPE
RM2040EQ _51 Engine / Hybrid System _014696 2AR-FXE INTAKE / EXHAUST _0074925 EXHAUST PIPE A

2AR-FXE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression spring.

Standard 42.0 mm (1.65 in.)
Minimum 40.5 mm (1.60 in.)

HINT:

If the length is less than the minimum, replace the compression spring.



b.

Fully insert a new gasket to the exhaust manifold converter sub-assembly.


c.
A104635
0.917,0.229 1.125,0.229 1.125,0.229 1.583,0.688 false 2.167,1.615 2.167,1.958 false 2.698,0.958 3.156,0.958 false 2.094,1.99 2.448,2.177 0.354,0.188 10 false *3 3.188,0.865 3.427,1.177 0.24,0.313 10 false *2 0.719,0.146 1.542,0.635 0.823,0.49 10 false *1
*1 Exhaust Manifold Converter Sub-assembly
*2 Wooden Block
*3 Gasket


Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly to the exhaust pipe support.


e.
A258941
1.146,0.583 0.885,0.188 0.885,0.188 0.729,0.188 false 0.781,1.198 0.917,1.198 0.917,1.198 1.104,0.906 false 2.406,0.76 2.5,0.219 2.5,0.219 2.677,0.219 false 0.542,0.104 1.552,0.479 1.01,0.375 10 false *1 2.698,0.135 3.365,0.563 0.667,0.427 10 false *3 0.604,1.115 1.427,1.615 0.823,0.5 10 false *2 0.417,1.438 1.219,1.917 0.802,0.479 10 false *a
*1 Exhaust Manifold Converter Sub-assembly
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 8.5 mm (0.335 in.)


Install the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 17420 2.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Connect the center exhaust pipe assembly to the exhaust pipe support.


c.

Install the center exhaust pipe assembly with the 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 3.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression spring.

Standard 40.0 mm (1.57 in.)
Minimum 38.5 mm (1.52 in.)

HINT:

If the length is less than the minimum, replace the compression spring.



b.

Fully insert a new gasket to the center exhaust pipe assembly.


c.
A104635
0.917,0.229 1.125,0.229 1.125,0.229 1.583,0.688 false 2.167,1.635 2.167,1.979 false 2.698,0.958 3.156,0.958 false 2.094,1.99 2.5,2.177 0.406,0.188 10 false *3 3.198,0.875 3.427,1.156 0.229,0.281 10 false *2 0.719,0.156 1.427,0.521 0.708,0.365 10 false *1
*1 Center Exhaust Pipe Assembly
*2 Wooden Block
*3 Gasket


Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the center exhaust pipe assembly.

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the tail exhaust pipe assembly to the 3 exhaust pipe supports.


e.
A258966
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.25,0.917 2.625,0.448 2.625,0.448 2.823,0.448 false 0.719,0.323 1.177,0.604 0.458,0.281 10 false *1 0.76,1.427 1.271,1.771 0.51,0.344 10 false *2 2.844,0.365 3.323,0.677 0.479,0.313 10 false *3 0.594,1.719 1.083,1.99 0.49,0.271 10 false *a
*1 Tail Exhaust Pipe Assembly
*2 Center Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 6.5 mm (0.256 in.)


Install the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 5.INSPECT FOR EXHAUST GAS LEAK