Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Not Using the Engine Support Bridge)
RM2040EQ _53 Suspension _014705 FRONT SUSPENSION _0074970 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  REMOVAL  


PROCEDURE

Hide 51100G 1.REMOVE FRONT FRAME ASSEMBLY

Hide 12361A 2.REMOVE FRONT ENGINE MOUNTING INSULATOR

Hide 12372A 3.REMOVE ENGINE MOUNTING INSULATOR LH

Hide 12362 4.REMOVE ENGINE MOUNTING INSULATOR RH

Hide 48829A 5.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 6.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as the LH side.


Hide 7.REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Remove the front stabilizer bar with 2 front stabilizer link assemblies from the front frame assembly.


Hide 8.REMOVE STEERING LINK ASSEMBLY

Hide 48069 9.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C167143

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly from the front frame assembly.

NOTICE:

When removing the bolt, keep the nut from rotating.



b.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.


Hide 48068 10.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 51227B 11.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.
C221242

Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.


Hide 52213A 12.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.


Hide 52216B 13.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.


Hide 52211J 14.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C169231C09
1.208,1 1.385,1 1.385,1 1.5,1.427 false 1.917,0.823 2.313,0.823 false 2.729,2.177 2.281,2.177 false 2.552,2.875 2.615,2.875 2.615,2.875 2.615,2.177 false 1.042,0.917 1.271,1.198 0.229,0.281 10 false *1 2.365,0.729 2.771,1.01 0.406,0.281 10 false SST 2.771,2.094 3.156,2.333 0.385,0.24 10 false SST
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265514C03
0.698,2.99 1,2.99 false 2.823,0.719 2.823,0.469 false 2.594,2.917 2.896,2.917 false 0.417,2.917 0.875,3.115 0.458,0.198 10 false SST 2.74,0.708 2.938,0.917 0.198,0.208 10 false *a 2.927,2.844 3.125,3.052 0.198,0.208 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting front cushion from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52217E 15.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C169231C10
1.198,1 1.375,1 1.375,1 1.49,1.427 false 1.917,0.823 2.313,0.823 false 2.74,2.177 2.292,2.177 false 2.563,2.875 2.625,2.875 2.625,2.875 2.625,2.177 false 1.021,0.917 1.271,1.177 0.25,0.26 10 false *1 2.354,0.729 2.823,0.99 0.469,0.26 10 false SST 2.781,2.083 3.25,2.396 0.469,0.313 10 false SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265515C03
0.677,3.031 0.99,3.031 false 2.708,0.781 2.708,0.427 false 2.677,2.917 2.99,2.917 false 0.396,2.969 0.854,3.167 0.458,0.198 10 false SST 2.625,0.781 2.938,0.938 0.313,0.156 10 false *a 3.01,2.854 3.323,3.01 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52215 16.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:

Perform the same procedure as the LH side.


Hide 17.REMOVE HOLE PLUG

a.

Remove 9 hole plugs from the front frame assembly.