Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074905 ENGINE ASSEMBLY A

2AR-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

·

The vehicle has a hybrid system that operates at voltages up to 650V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM

Hide 64718C 3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64711 5.REMOVE LUGGAGE COMPARTMENT FLOOR MAT

Hide 64717A 6.REMOVE LUGGAGE COMPARTMENT FRONT TRIM COVER

Hide G92QA 7.REMOVE NO. 8 HYBRID VEHICLE BATTERY SHIELD PANEL

Hide 9. DISCHARGE FUEL SYSTEM PRESSURE

Hide 10. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 11.SECURE STEERING WHEEL

Hide 12.REMOVE FRONT WHEELS

Hide 53852K 13.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51442C 14.REMOVE ENGINE UNDER COVER LH

Hide 53851Z 15.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441C 16.REMOVE ENGINE UNDER COVER RH

Hide 53737B 17.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 18.REMOVE FRONT FENDER APRON SEAL RH

Hide 12601B 23.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A259744

Lift the rear of the engine cover to detach the cover from the 2 pins, and then lift the front of the engine cover to detach the cover from the pin and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide 53295E 24.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 27.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 17750A 28.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A259747

Remove the 2 bolts and inlet air cleaner assembly.


Hide 17735 29.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 30.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


Hide 17701 31.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A259768C02
1.096,1.151 1.251,1.151 false 1.279,1.054 1.431,1.208 0.152,0.154 10 *a
*a Projection


Remove the 2 bolts and air cleaner case sub-assembly.


Hide G1143C 38.REMOVE NO. 3 MOTOR CABLE BRACKET

Hide 42.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

Hide 82113 44.DISCONNECT NO. 3 ENGINE ROOM WIRE

Hide G9228A 45.REMOVE NO. 4 INVERTER COOLING HOSE

Hide G90A0A 46.REMOVE NO. 1 INVERTER COOLING HOSE ASSEMBLY

Hide G9200 47.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 82124 48.DISCONNECT NO. 4 ENGINE WIRE

a.
A280055

Remove the 2 wire harness clamps and disconnect the No. 4 engine wire from the fan shroud.


Hide 82121 49.DISCONNECT ENGINE WIRE

a.
A259755

Disconnect the 4 connectors and disconnect the wire harness clamp.


b.
A259753

Remove the bolt and disconnect the earth wire from the body.


c.
A259754

Pull up the lever to disconnect the ECM connector.


d.

Disconnect the wire clamp.


Hide 33820B 50.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A268022

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


b.

Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.


c.

Remove the clip from the transmission control cable assembly.


d.
C243612

Disconnect the transmission control cable assembly from the 2 transmission control brackets.


Hide 16571C 51.DISCONNECT NO. 1 RADIATOR HOSE

a.
A259752

Remove the hose clamp to disconnect the air fuel ratio sensor wire from the No. 1 radiator hose.


b.

Disconnect the No. 1 radiator hose.


Hide G9229A 52.DISCONNECT NO. 5 INVERTER COOLING HOSE

a.
A259746

Disconnect the No. 5 inverter cooling hose from the hybrid vehicle transaxle assembly.


Hide 87245 53.DISCONNECT INLET HEATER WATER HOSE

a.
A260220

Disconnect the inlet heater water hose.


Hide 87246 54.DISCONNECT OUTLET HEATER WATER HOSE

a.
A260221

Disconnect the outlet heater water hose.


Hide 77251B 55.DISCONNECT FUEL MAIN TUBE

a.
A203577

Release the claw and remove the No. 1 EFI fuel pipe clamp.


b.
A167796

Pinch the fuel tube connector and then pull out the fuel main tube.

NOTICE:
·

Check for dirt and foreign objects on the pipe and around the connector. Clean if necessary and then disconnect the connector.

·

Disconnect the connector by hand.

·

Do not bend, fold or rotate the nylon tube.

·

If the pipe and connector are stuck together, push and pull the connector until it becomes free.

·

Put the pipe and connector ends in vinyl bags to prevent damage and contamination.




Hide 12327A 56.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A259961

Remove the 2 bolts and No. 2 engine mounting stay RH.


Hide 82284 57.SEPARATE EARTH WIRE

a.
A259960

Remove the bolt and separate the earth wire from the engine moving control rod sub-assembly.


Hide 12309 58.REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

a.
A259959

Remove the 4 bolts and engine moving control rod sub-assembly.


Hide 88704 59.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 60.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 16572D 61.DISCONNECT NO. 2 RADIATOR HOSE

a.
A260222

Disconnect the No. 2 radiator hose.


Hide 17410 62.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 45220 63.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 43502H 64.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 65.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 66.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 67.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89543 68.SEPARATE FRONT SPEED SENSOR LH

Hide 89542 69.SEPARATE FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 70.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 71.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 72.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 73.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43502C 74.SEPARATE FRONT AXLE ASSEMBLY LH

Hide 43501C 75.SEPARATE FRONT AXLE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 11361J 76.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A259962

Remove the flywheel housing under cover.


Hide 77.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A260219C02
0.74,1.656 0.75,1.646 false
V100145

Attachment Installation Position


Set an engine lifter.

NOTICE:
·

Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

·

To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed or removed from an engine stand.

·
A346911C01
2.354,1.635 2.354,1.26 true 2.292,1.656 2.604,1.854 0.313,0.198 10 true *1
*1 No. 2 Motor Water Jacket Cover Assembly


To prevent coolant leaks, do not position the height adjustment attachments or plate lift attachments under the No. 2 motor water jacket cover assembly.




b.
A260218C02
3.135,0.292 3.281,0.448 0.146,0.156 10 false *1 3.177,2.417 3.427,2.635 0.25,0.219 10 true *1 0.073,2.406 0.24,2.573 0.167,0.167 10 true *1 0.104,0.292 0.25,0.448 0.146,0.156 10 false *1
*1 Nut


Remove the 4 bolts, 2 nuts, and frame side rail plate RH and LH.


c.

Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.


d.

Operate the engine lifter and remove the engine assembly from the vehicle.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.





Hide 82121 78.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine with transaxle.


Hide 43420 79.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43420G 80.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43410 81.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

Hide 51100G 82.REMOVE FRONT FRAME ASSEMBLY

a.
A259957

Remove the bolt and disconnect the No. 4 engine wire from the front frame assembly.


b.
A255456

Remove the nut and separate the engine mounting insulator LH.


c.
A260223

Remove the bolt and separate the front engine mounting insulator.


d.
A255455

Remove the nut and separate the engine mounting insulator RH.


e.

Remove the front frame assembly.


f.

Using a height adjustable attachment and plate lift attachment, place the engine assembly on a flat level surface.

NOTICE:
·

Using a height adjustable attachment and plate lift attachment, place the engine assembly with transaxle horizontally.

·

To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.

·

Using an engine sling device and engine lift, secure the engine assembly before service.




Hide 12361A 83.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A259963

Remove the 3 nuts and front engine mounting insulator.

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.



Hide 12372A 84.REMOVE ENGINE MOUNTING INSULATOR LH

a.
A255459

Remove the 2 hole plugs from the front frame assembly.


b.

Remove the 3 nuts and engine mounting insulator LH.

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



Hide 12362 85.REMOVE ENGINE MOUNTING INSULATOR RH

a.
A255460

Remove the 2 hole plugs from the front frame assembly.


b.

Remove the 3 nuts and engine mounting insulator RH.

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.



Hide 12315A 86.REMOVE ENGINE MOUNTING BRACKET RH

a.
A196634

Remove the 3 bolts and engine mounting bracket RH.


Hide 43457 87.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A196633

Remove the 3 bolts and drive shaft bearing bracket.


Hide 88370 88.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

Hide 30900 89.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 90.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 92.INSTALL ENGINE STAND

a.

Install the engine onto an engine stand with the bolts.