Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM2040EQ _53 Suspension _014706 REAR SUSPENSION _0074972 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48258C 1.INSTALL REAR LOWER COIL SPRING INSULATOR

a.
C132468C08
2.052,1.198 3.052,1.198 false 3.094,1.094 3.323,1.354 0.229,0.26 10 false *a
*a Protrusion


Install the rear lower coil spring insulator onto the rear shock absorber assembly.

NOTICE:

Align the protrusion of the rear lower coil spring insulator and the hole in the rear shock absorber assembly.



Hide 48341B 2.INSTALL REAR NO. 1 SPRING BUMPER

a.

Install the rear No. 1 spring bumper to the rear shock absorber assembly.

NOTICE:

Face the smaller diameter end of the rear No. 1 spring bumper downward.



Hide 48231B 3.INSTALL REAR COIL SPRING

a.
C265188N01
2.563,1.625 2.563,1.427 2.563,1.427 2.781,1.427 false 2.833,1.365 3.292,1.563 0.458,0.198 10 SST

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C275706C11
0.323,0.167 0.635,0.479 0.313,0.313 10 false *a 0.354,2.479 0.698,2.792 0.344,0.313 10 false *b
*a Correct
*b Incorrect


Attach the arms of SST to the diameter of the rear coil spring.

CAUTION:
·

Make sure that the rear coil spring is installed so that the distance between the upper and lower arms of SST is at the maximum.

·

Make sure that the claws of the arms are securely attached.




c.

Using SST, compress the rear coil spring.

CAUTION:
·

If the rear coil spring bends during compression, immediately stop compression and reinstall SST.

·

Do not excessively compress the rear coil spring so that the coils contact each other.

·

Do not use an impact wrench. It will damage SST.




d.
C265189N01
2.385,1.396 2.385,1.542 2.385,1.542 2.688,1.542 false 2.708,1.469 3.146,1.719 0.438,0.25 10 SST

Install the rear coil spring to the rear shock absorber assembly.

NOTICE:
·

The smaller diameter end of the rear coil spring must face upward.

·

Make sure to fit the end of the rear coil spring that has the larger diameter into the depression of the rear lower coil spring insulator.




Hide 48760B 4.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

a.
C239086C05
1.188,1.125 1.969,1.927 1.969,1.927 2.781,1.167 false 1.896,1.917 2.167,2.135 0.271,0.219 10 false *a
*a Notch


Install the rear suspension support assembly to the rear shock absorber assembly.

NOTICE:

Align the notches of the piston rod and the rear suspension support assembly as shown in the illustration before installing the rear suspension support assembly.



b.
C265187C06
2.292,2.885 2.292,2.99 2.292,2.99 2.563,2.99 false 0.708,1.052 1.063,0.26 1.063,0.26 1.458,0.26 false 2.625,2.906 3.073,3.135 0.448,0.229 10 false SST 1.479,0.167 1.76,0.469 0.281,0.302 10 false *a
*a Notch
V100135

Outside of the Vehicle


Align the notches of the rear shock absorber assembly with the notch of the rear suspension support assembly so that the notches face the outside of the vehicle.


Hide 48760D 5.INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER COLLAR

a.

Install the rear support to rear shock absorber collar to the rear shock absorber assembly.


Hide 48760C 6.TEMPORARILY TIGHTEN REAR SUPPORT TO REAR SHOCK ABSORBER NUT

a.

Temporarily tighten a new rear support to rear shock absorber nut to the rear shock absorber assembly.


b.
C239084N04
3.146,0.938 3.365,1.167 0.219,0.229 10 false 5° 3.146,1.135 3.375,1.375 0.229,0.24 10 false 5°

Release the rear coil spring while adjusting the rear suspension support assembly to the position shown in the illustration, and remove SST from the rear coil spring.

NOTICE:

Do not use an impact wrench. It will damage SST.


HINT:

Make sure to align the outer stud bolt on the rear suspension support assembly to within +/- 5° of the center of the rear shock absorber lower bracket as shown in the illustration.



Hide 7.INSTALL REAR SHOCK ABSORBER WITH COIL SPRING

a.
C144663

Install the rear shock absorber with coil spring to the rear axle carrier sub-assembly and insert the 2 bolts from the rear of the vehicle.


b.

Slowly jack up the suspension using a wooden block and install the rear shock absorber with coil spring (upper side) to the vehicle.


c.

Install the 3 nuts to the upper side of the rear shock absorber with coil spring.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


d.

Install the 2 nuts to the lower side of the rear shock absorber with coil spring.

Torque:
180 N*m (1835 kgf*cm, 133 ft.*lbf)

NOTICE:

When installing the nuts, keep the bolts from rotating.



e.

Fully tighten the rear support to rear shock absorber nut.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 89516D 8.INSTALL SKID CONTROL SENSOR WIRE

a.

Install the skid control sensor wire to the rear shock absorber assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 47319F 9.INSTALL REAR FLEXIBLE HOSE

a.

Install the rear flexible hose to the rear shock absorber assembly with the bolt.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 48840A 10.INSTALL REAR STABILIZER LINK ASSEMBLY

a.

Install the rear stabilizer link assembly to the rear shock absorber assembly with the nut.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.


Hide 48753C 11.INSTALL REAR NO. 1 SUSPENSION SUPPORT COVER

a.

Engage the 4 claws and install the rear No. 1 suspension support cover.


Hide 12.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 13.INSTALL REAR SIDE SEATBACK ASSEMBLY

Hide 14.INSPECT AND ADJUST REAR WHEEL ALIGNMENT