Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2040EQ _55 Steering _014713 POWER ASSIST SYSTEMS _0074999 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511/11  Torque Sensor 1 Malfunction  C1512/11  Torque Sensor 2 Malfunction  C1513/11  Torque Sensor Deviation Excessive  C1514/11  Torque Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The torque sensor converts the steering wheel rotation torque into electric signals and sends them to the power steering ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1511/11 Torque Sensor 1 Malfunction Torque sensor malfunction
·

Torque sensor (built into electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS Warning Light: Comes on Power switch on (IG) again
C1512/11 Torque Sensor 2 Malfunction Torque sensor malfunction
·

Torque sensor (built into electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS Warning Light: Comes on Power switch on (IG) again
C1513/11 Torque Sensor Deviation Excessive Torque sensor malfunction
·

Torque sensor (built into electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS Warning Light: Comes on Power switch on (IG) again
C1514/11 Torque Sensor Power Supply Voltage Malfunction Torque sensor malfunction
·

Torque sensor (built into electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS Warning Light: Comes on Power switch on (IG) again

WIRING DIAGRAM

C240198E02
4.446,3.069 6.436,3.29 1.99,0.221 10 Power Steering ECU Assembly 0.558,2.946 3.062,3.31 2.503,0.365 10 Torque Sensor (built into Electric Power Steering Column Sub-assembly) 4.628,0.73 5.081,0.951 0.453,0.221 10 TRQ1 4.439,0.665 4.557,0.847 0.118,0.183 10 7 4.439,1.076 4.571,1.258 0.132,0.183 10 2 4.439,1.515 4.571,1.697 0.132,0.183 10 3 4.439,1.959 4.557,2.141 0.118,0.183 10 5 4.439,2.379 4.557,2.561 0.118,0.183 10 1 4.628,1.589 5.081,1.81 0.453,0.221 10 TRQV 4.628,2.037 5.081,2.258 0.453,0.221 10 TRQF 4.628,1.15 5.081,1.371 0.453,0.221 10 TRQ2 4.628,2.472 5.081,2.693 0.453,0.221 10 TRQG 4.446,2.893 4.687,3.075 0.241,0.182 10 a

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - ECU)
a.

Check the connection condition of the torque sensor connector.

OK:

Torque sensor connector is securely connected to the power steering ECU assembly.



Result:
Proceed to
OK
NG



OK

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)

NG

CONNECT CONNECTOR

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)
a.
C238944C05
1.167,1.229 1.531,1.469 0.365,0.24 2.125,2.615 1.448,2.021 false 1.667,2.833 1.438,2.104 false 1.302,2.021 1.083,2.802 false 0.094,0.052 0.542,0.344 0.448,0.292 10 *a 1.938,2.646 2.5,2.979 0.563,0.333 10 TRQG 1.313,1.271 1.615,1.688 0.302,0.417 10 a 0.844,2.854 1.698,3.24 0.854,0.385 10 TRQV 1.458,2.854 2.115,3.24 0.656,0.385 10 TRQF
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a-3 (TRQV) - a-1 (TRQG) Power switch on (IG) 8.5 to 10.5 V
a-5 (TRQF) - a-1 (TRQG) Power switch on (IG) 3.35 to 3.37 V



Result:
Proceed to
OK
NG



OK

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)

NG

REPLACE POWER STEERING ECU ASSEMBLY

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)
a.
C238944C06
1.167,1.229 1.531,1.469 0.365,0.24 2.125,2.615 1.448,2.021 false 1.677,2.823 1.385,2.01 false 1.302,2.104 1.083,2.802 false 0.094,0.052 0.708,0.573 0.615,0.521 10 *a 1.938,2.646 2.563,2.969 0.625,0.323 10 TRQG 1.313,1.281 1.563,1.74 0.25,0.458 10 a 0.844,2.813 1.563,3.25 0.719,0.438 10 TRQ1 1.458,2.854 2.115,3.229 0.656,0.375 10 TRQ2
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the power switch on (READY).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition (Steering Wheel Position) Specified Condition
a-7 (TRQ1) - a-1 (TRQG) Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel being turned to the right with vehicle stopped
2.5 to 4.7 V
Power switch on (READY)
Steering wheel being turned to the left with vehicle stopped
0.3 to 2.5 V
a-2 (TRQ2) - a-1 (TRQG) Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel being turned to the right with vehicle stopped
0.3 to 2.5 V
Power switch on (READY)
Steering wheel being turned to the left with vehicle stopped
2.5 to 4.7 V



c.

Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

Standard Voltage:
Inspection Item Condition (Steering Wheel Position) Specified Condition
Sum of voltage between a-7 (TRQ1) and a-1 (TRQG) and voltage between a-2 (TRQ2) and a-1 (TRQG) Power switch on (READY)
Steering wheel not being turned (without load)
Between 4.85 V and 5.35 V
Power switch on (READY)
Steering wheel being turned to the right with vehicle stopped
Power switch on (READY)
Steering wheel being turned to the left with vehicle stopped



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY