Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2040EQ _55 Steering _014713 POWER ASSIST SYSTEMS _0074999 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (USING THE INTELLIGENT TESTER)


a.

Turn the power switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Read the DTCs following the display on the intelligent tester. Enter the following menus: Chassis / EMPS / DTC.

Chassis > EMPS > Trouble Codes
50001 142

f.

Refer to the Diagnostic Trouble Code Chart for DTC information.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



CHECK DTCs (USING SST CHECK WIRE)


a.
C248264C30
1.604,0.813 1.604,0.406 false 1.844,1.854 1.844,1.479 false 1.51,0.219 1.74,0.448 0.229,0.229 10 false CG 1.771,1.875 1.99,2.021 0.219,0.146 10 false TC 0.177,0.125 0.427,0.458 0.25,0.333 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the power switch on (IG).


c.
C276865C02
1.917,3.396 2.083,2.75 false 1.438,3.396 1.583,2.917 false 2.271,3.396 2.417,2.917 false 1.167,3.396 1.333,2.75 false 1.083,3.396 1,2.917 false 0.167,0.146 0.344,0.333 0.177,0.188 10 *1 0.573,1.26 0.813,1.448 0.24,0.188 10 *a 0.583,1.75 0.885,1.938 0.302,0.188 10 *b 0.167,2.396 0.344,2.583 0.177,0.188 10 *2 1.281,4.052 1.844,4.229 0.563,0.177 10 *d 2.292,4.042 2.854,4.219 0.563,0.177 10 *e 2.104,4.354 2.771,4.531 0.667,0.177 10 (*c) 1.177,0.844 1.479,1.031 0.302,0.188 10 0.25 2.208,0.615 2.51,0.802 0.302,0.188 10 0.25 0.833,3.417 0.948,3.604 0.115,0.188 10 4 0.885,2.75 1.115,2.938 0.229,0.188 10 0.5 1.25,2.583 1.479,2.771 0.229,0.188 10 0.5 1.5,2.75 1.729,2.938 0.229,0.188 10 1.5 2.365,2.75 2.594,2.938 0.229,0.188 10 0.5 2,2.583 2.229,2.771 0.229,0.188 10 2.5 0.26,3.469 0.5,3.656 0.24,0.188 10 *a 0.271,3.906 0.573,4.094 0.302,0.188 10 *b 2.708,1.99 3.167,2.333 0.458,0.344 10 (*c)
*1 Normal code
*2 Codes 21 and 22
*a ON
*b OFF
*c Seconds
*d Code 21
*e Code 22


Read and write down any DTCs indicated by the EPS warning light on the combination meter. Refer to the chart on the left for examples of a normal code and DTCs 21 and 22.

HINT:
·

If the EPS warning light does not blink to display any DTCs set or the normal code, inspect the circuit shown in the table below.

Trouble Area Link
EPS warning light circuit (Click here)

·

If two or more malfunctions are detected simultaneously, DTCs will be displayed in ascending numerical order.




d.

Refer to the Diagnostic Trouble Code Chart for DTC information.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



CLEAR DTC (USING THE INTELLIGENT TESTER)


a.

Turn the power switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Clear the DTCs following the display on the intelligent tester. Enter the following menus: Chassis / EMPS / DTC / Clear.

Chassis > EMPS > Clear DTCs
50002 142

f.

Turn the power switch off.


g.

Disconnect the intelligent tester from the DLC3.



CLEAR DTCs (USING SST CHECK WIRE)


a.
C248264C31
1.604,0.813 1.604,0.406 false 1.594,1.51 1.396,1.823 false 1.865,1.5 2.031,1.833 false 1.5,0.219 1.802,0.448 0.302,0.229 10 false CG 1.281,1.875 1.521,2.073 0.24,0.198 10 false TS 2,1.875 2.24,2.083 0.24,0.208 10 false TC 0.125,0.146 0.323,0.448 0.198,0.302 10 false *1
*1 DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3, and also terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


b.

Turn the power switch on (READY).


c.

Disconnect and reconnect terminal 13 (TC) of the DLC3 4 times or more within 8 seconds.


d.

Check that the EPS warning light blinks a code to indicate normality.


e.

Turn the power switch off.


f.

Remove SST from the DLC3.