Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2040EQ _55 Steering _014713 POWER ASSIST SYSTEMS _0074999 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552/22  PIG Power Supply Voltage Malfunction  C1554/23  Power Supply Relay Failure  


DESCRIPTION

When a problem occurs in the power steering system, the power source relay circuit is shut off to stop the power assist.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1552/22 PIG Power Supply Voltage Malfunction PIG power source circuit malfunction inside ECU
·

EPS fuse

·

PIG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


EPS Warning Light: Comes on Power switch on (IG) again or after normal confirmation
C1554/23 Power Supply Relay Failure Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

ECU wire sub-assembly

·

Power steering ECU assembly


EPS Warning Light: Comes on Power switch on (IG) again

WIRING DIAGRAM

C250101E03
5.104,0.802 5.427,0.979 0.323,0.177 10 false PIG 4.958,2.833 5.385,3.094 0.427,0.26 10 false j2 4.906,0.677 5.052,0.854 0.146,0.177 10 false 1 4.906,2.125 5.063,2.302 0.156,0.177 10 false 2 5.104,2.25 5.552,2.427 0.448,0.177 10 false PGND 1.76,1.01 2.125,1.344 0.365,0.333 10 false EPS 0.896,1.365 1.469,1.542 0.573,0.177 10 false MAIN 1.021,2.281 1.594,2.906 0.573,0.625 10 false Auxiliary Battery 4.958,3 6.969,3.333 2.01,0.333 10 false Power Steering ECU Assembly 3.208,0.802 3.531,0.979 0.323,0.177 10 false Ij1 3.229,0.583 3.375,0.76 0.146,0.177 10 false 1 4.229,0.917 4.552,1.094 0.323,0.177 10 false *1 3.802,2.365 4.125,2.542 0.323,0.177 10 false *1 0.313,3.302 2.125,3.583 1.813,0.281 10 false *1: ECU Wire Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (PIG POWER SUPPLY)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.READ VALUE USING INTELLIGENT TESTER (PIG POWER SUPPLY)
a.

Turn the power switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "PIG Power Supply" in the Data List and read the value displayed on the intelligent tester.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to active motor Min.: 0.0000 V
Max.: 20.1531 V
Power switch on (READY) and steering wheel being turned: 9 to 16 V -
Chassis > EMPS > Data List
Tester Display
PIG Power Supply
50003 142 10
OK:

The normal condition value is displayed on the intelligent tester.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - ECU WIRE SUB-ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C240360C02
0.5,0.677 0.948,0.958 0.448,0.281 2.49,1.146 1.854,1.344 false 0.25,0.146 0.719,0.521 0.469,0.375 10 *a 2.521,1.042 2.938,1.281 0.417,0.24 10 PIG 0.646,0.74 1.083,1.156 0.438,0.417 10 Ij1
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the Ij1 connector from the ECU wire sub-assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ij1-1 (PIG) - Body ground Always 9 to 16 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240344C03
0.229,1 0.677,1.281 0.448,0.281 2.146,1.188 2.229,1.781 false 1.198,1.198 1.115,1.792 false 0.146,0.125 0.74,0.552 0.594,0.427 10 *a 0.396,1.052 0.854,1.375 0.458,0.323 10 j2 2.094,1.833 2.896,2.177 0.802,0.344 10 PGND 1.021,1.823 1.521,2.146 0.5,0.323 10 PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the Ij1 connector to the ECU wire sub-assembly.


b.

Disconnect the power steering ECU assembly j2 connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j2-1 (PIG) - Body ground Always 9 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY