Home › Power Source / Network › POWER DISTRIBUTION › INTEGRATION RELAY › 2012.02–2015.04
RM2040EQ _57 Power Source / Network _014720 POWER DISTRIBUTION _0075040 INTEGRATION RELAY G

POWER DISTRIBUTION  INTEGRATION RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 82720 1.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (SIGNAL READING CHECK)

NOTICE:

Both present and history signal readings will be cleared if the engine room junction block assembly is removed. Make sure not to remove it before inspection.


HINT:

The signal readings of the engine room junction block assembly can be checked by inspecting the voltage at the diagnosis terminal.


a.

Signal reading check

i.

Turn the power switch on (IG).


ii.
E227859
1.167,1.531 1.844,1 false 0.958,1.521 1.375,1.823 0.417,0.302 10 false *b 0.208,0.115 0.51,0.365 0.302,0.25 10 false *a
*a Component with harness connected
(Engine Room Junction Block Assembly)
*b Diagnosis Terminal


Connect the positive (+) terminal of a voltmeter to the engine room junction block assembly and the negative (-) terminal to the body ground.


iii.

Using the illustration below as a reference, determine whether any channels are malfunctioning based on the observed signal reading.

E228235E05
1.865,2.708 2.156,2.906 0.292,0.198 10 Unit 2.281,2.708 2.542,2.885 0.26,0.177 10 ch0 2.688,2.708 2.948,2.885 0.26,0.177 10 ch1 3.083,2.708 3.344,2.885 0.26,0.177 10 ch2 4.448,2.708 4.792,2.938 0.344,0.229 10 Unit 4.885,2.708 5.219,2.938 0.333,0.229 10 ch0 5.281,2.708 5.635,2.948 0.354,0.24 10 ch1 5.677,2.708 6,2.927 0.323,0.219 10 ch2 3.781,2.708 4.042,2.885 0.26,0.177 10 ch9 6.552,2.708 6.906,2.979 0.354,0.271 10 ch9 4.51,4.25 4.802,4.448 0.292,0.198 10 Unit 4.896,4.25 5.156,4.427 0.26,0.177 10 ch0 5.375,4.25 5.635,4.427 0.26,0.177 10 ch1 5.813,4.25 6.073,4.427 0.26,0.177 10 ch2 6.521,4.25 6.875,4.479 0.354,0.229 10 ch9 1.927,4.25 2.219,4.448 0.292,0.198 10 Unit 2.427,4.25 2.688,4.427 0.26,0.177 10 ch0 2.823,4.25 3.083,4.427 0.26,0.177 10 ch1 3.208,4.25 3.469,4.427 0.26,0.177 10 ch2 3.771,4.25 4.031,4.427 0.26,0.177 10 ch9 1.313,1.875 1.74,2.031 0.427,0.156 10 8 sec. 2.073,1.875 2.51,2.031 0.438,0.156 10 1 sec. 2.531,1.885 2.969,2.042 0.438,0.156 10 1 sec. 4.667,1.875 5.104,2.031 0.438,0.156 10 1 sec. 5.104,1.875 5.542,2.031 0.438,0.156 10 1 sec. 4.073,1.875 4.5,2.031 0.427,0.156 10 4 sec. 1.917,3.396 2.354,3.552 0.438,0.156 10 3 sec. 5.427,4.698 5.865,4.854 0.438,0.156 10 1 sec. 5.875,4.698 6.313,4.854 0.438,0.156 10 1 sec. 5.271,3.396 5.708,3.552 0.438,0.156 10 3 sec. 2.49,4.698 2.927,4.854 0.438,0.156 10 1 sec. 2.021,4.698 2.458,4.854 0.438,0.156 10 1 sec. 1.063,0.781 2.094,1.083 1.031,0.302 10 Present Header 3.802,0.781 4.823,1.052 1.021,0.271 10 History Header 2.156,1.063 3.667,1.26 1.51,0.198 10 Present Signal Reading 4.938,1.063 6.427,1.26 1.49,0.198 10 History Signal Reading 6.042,2.708 6.354,2.917 0.313,0.208 10 ch3 0.115,2.333 0.719,2.75 0.604,0.417 10 Normal Condition: 0.115,3.865 0.833,4.24 0.719,0.375 10 Abnormal Condition*: 1.875,5.104 5.969,5.479 4.094,0.375 10 *: The example shows a malfunction for "Unit" in the present signal reading and for "ch1" in the history signal reading. 0.938,2.313 1.146,2.469 0.208,0.156 10 Hi 0.938,2.531 1.177,2.688 0.24,0.156 10 Lo 0.938,3.844 1.146,4 0.208,0.156 10 Hi 0.938,4.052 1.177,4.208 0.24,0.156 10 Lo 0.417,4.865 1.51,5.073 1.094,0.208 10 Hi: 7 V or higher 0.417,5.219 1.375,5.427 0.958,0.208 10 Lo: Below 2 V

HINT:
·

Present signal reading and history signal reading will be displayed alternately after the power switch is turned on (IG). By measuring the duration of each header, the present signal reading and history signal reading can be recognized.

·

A unit malfunction indicates an internal malfunction of the engine room junction block assembly. If a malfunction is detected for any channel from channel 0 to 9, an electrical load connected to the engine room junction block assembly may be malfunctioning or there may be a short in the engine room junction block assembly circuit or in the wire harness.

·

The present signal reading will be stored as a history signal reading when electrical loads are operated after a malfunctioning part returns to normal.

·

Both present and history signal readings can be cleared by disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Depending on the specification, different electrical loads connected to channels 0 to 9 are provided. Refer to the table below:

Channel Connected Electrical Load
w/ Front Fog Light w/o Front Fog Light
ch0 Back-up lights -
ch1 -
ch2 Mirror heater
ch3 -
ch4 -
ch5 Rear fog lights Rear window defogger wire
ch6 Front fog lights -
ch7 Rear window defogger wire Back-up lights
ch8 High beam headlight LH
ch9 High beam headlight RH





Hide 82720 2.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)

a.

Results of signal reading check

i.

Depending on the signal reading, perform troubleshooting according the table below.

Output Signal Reading Repair Method
Normal Continue troubleshooting for each system.
The unit is malfunctioning. Replace the engine room junction block.
A malfunction in a channel (ch0 to ch9)
1.

Check for a short in the wire harnesses between the engine room junction block assembly and each electrical load.

2.

Inspect each of the electrical loads.

3.

Replace the engine room junction block.



HINT:

Make sure to clear the signal readings by disconnecting the cable from the negative (-) auxiliary battery terminal after replacement or repair of the malfunctioning part.



ii.
E265558C05
1.479,2.125 1.896,2.354 0.417,0.229 1.906,4.094 1.792,3.615 false 0.188,0.115 0.5,0.313 0.313,0.198 10 *a 1.615,2.146 1.927,2.344 0.313,0.198 10 1F 1.823,4.125 2.219,4.375 0.396,0.25 10 IGN
*a Component without engine room junction block assembly
(Engine Room Relay Block and Junction Block Assembly)


If no signal readings are output, perform troubleshooting according to the following troubleshooting procedure.

1.

Remove the engine room junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL

2.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1F-15 (IGN) - Body ground Power switch on (IG) 11 to 14 V


If the result is not as specified, repair or replace the wire harness or connector.