Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075041 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN
·

Errors in LIN communication between ECUs or an open or short in communication lines

·

LIN communication error detected by the certification ECU (smart key ECU assembly) 3 times in a row.


·

Certification ECU (smart key ECU assembly)

·

Power management control ECU

·

Steering lock ECU (steering lock actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

B281971
1.471,1.873 2.816,2.212 1.345,0.339 10 Power Management Control ECU 4.595,1.887 6.139,2.226 1.544,0.339 10 Certification ECU (Smart Key ECU Assembly) 4.455,3.75 6.279,4.089 1.824,0.339 10 Steering Lock ECU (Steering Lock Actuator Assembly) 0.913,4.313 2.529,4.471 1.616,0.159 10 : LIN Communication Line 2.984,0.99 3.199,1.149 0.215,0.159 10 11 2.585,1.132 2.9,1.29 0.315,0.159 10 LIN2 4.357,0.99 4.533,1.149 0.176,0.159 10 12 4.616,1.132 4.857,1.29 0.241,0.159 10 LIN 4.434,2.867 4.534,3.026 0.1,0.159 10 5 4.616,3.009 4.857,3.168 0.241,0.159 10 LIN 4.455,3.582 4.724,3.741 0.269,0.159 10 I24 4.595,1.719 4.915,1.877 0.319,0.159 10 I87 1.471,1.705 1.763,1.863 0.292,0.159 10 I4

CAUTION / NOTICE / HINT

NOTICE:
·

If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to the Service Bulletin).

·

If the steering lock ECU (steering lock actuator assembly) is replaced, register the ECU code (refer to the Service Bulletin).

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - EACH ECU)
a.

Disconnect the I24 steering lock ECU (steering lock actuator assembly) connector.


b.

Disconnect the I87 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the I4 power management control ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-12 (LIN) - I4-11 (LIN2) Always Below 1 Ω
I87-12 (LIN) - I24-5 (LIN) Always Below 1 Ω
I4-11 (LIN2) - Body ground Always 10 kΩ or higher
I24-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT (STEERING LOCK ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DTC OUTPUT (STEERING LOCK ECU ASSEMBLY)
a.

Reconnect the I87 certification ECU (smart key ECU assembly) connector.


b.

Reconnect the I4 power management control ECU connector.


c.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

d.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

3.CHECK DTC OUTPUT (POWER MANAGEMENT CONTROL ECU)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

3.CHECK DTC OUTPUT (POWER MANAGEMENT CONTROL ECU)
a.

Reconnect the I24 steering lock ECU (steering lock actuator assembly) connector.


b.

Disconnect the I4 power management control ECU connector.


c.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

d.

Recheck for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B