Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075041 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2287  LIN Communication Master Malfunction  


DESCRIPTION

This DTC is stored when there is an open, short or ECU communication malfunction between the power management control ECU and certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area
B2287 LIN Communication Master Malfunction There is an open, short or ECU communication malfunction between power management control ECU and certification ECU (smart key ECU assembly).
·

Power management control ECU

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

B203745
1.147,2.445 2.767,2.592 1.619,0.147 10 : LIN Communication Line 0.885,1.771 2.964,1.918 2.079,0.147 10 Power Management Control ECU 0.885,1.618 1.152,1.775 0.267,0.156 10 I4 4.436,1.618 4.717,1.77 0.281,0.152 10 I87 4.436,1.771 6.018,2.085 1.582,0.314 10 Certification ECU (Smart Key ECU Assembly) 2.427,1.044 2.75,1.195 0.323,0.151 10 LIN2 4.436,1.044 4.694,1.191 0.258,0.147 10 LIN 2.806,0.913 2.983,1.051 0.177,0.138 10 11 4.202,0.913 4.405,1.093 0.203,0.179 10 12

CAUTION / NOTICE / HINT

NOTICE:
·

If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to the Service Bulletin).

·

When using the intelligent tester to troubleshoot with the power switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Clear DTCs
50002 223
Body Electrical > Entry&Start > Clear DTCs
50002 125

b.

Recheck for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Check the both "Entry&Start" and "Power Source Control" DTCs.


Result:
Result Proceed to
Only DTC B2287 is output. A
DTC B2287 and B2785 are output simultaneously. B




A

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)

B

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the I4 power management control ECU and I87 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-11 (LIN2) - I87-12 (LIN) Always Below 1 Ω
I4-11 (LIN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU.

Click herePower Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL

Result:
Proceed to
NEXT




NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Clear the DTC.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Clear DTCs
50002 223

b.

Recheck for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

DTC B2287 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)