Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Steering sensor branch line or connector

·

Power source circuit of steering sensor

·

Steering sensor ground circuit

·

Steering sensor



WIRING DIAGRAM

C252897E12
2.167,1.281 2.167,0.865 2.167,0.865 2.052,0.865 false 4.521,1.281 4.635,0.646 4.635,0.646 4.792,0.646 false 1.417,4.99 3.292,5.156 1.875,0.167 10 false : CAN Main Bus Line (CANH) 1.417,5.406 3.302,5.583 1.885,0.177 10 false : CAN Main Bus Line (CANL) 4.406,4.99 6.125,5.177 1.719,0.188 10 false : CAN Branch Line (CANH) 4.406,5.396 6.146,5.563 1.74,0.167 10 false : CAN Branch Line (CANL) 1.448,3.677 2.323,3.844 0.875,0.167 10 false Trouble Area 3.885,4.073 5.115,4.458 1.229,0.385 10 false Steering Sensor 0.865,2.208 1.354,2.365 0.49,0.156 10 false 120 Ω 6.073,2.208 6.563,2.365 0.49,0.156 10 false 120 Ω 0.167,0.76 2.156,1.01 1.99,0.25 10 false CAN Junction LH1 Connector 3.177,0.563 3.656,0.813 0.479,0.25 10 false DLC3 3.833,3.26 4.26,3.406 0.427,0.146 10 false CANH 4.365,3.26 4.781,3.406 0.417,0.146 10 false CANL 3.604,3.844 3.823,4.021 0.219,0.177 10 false IG 2.479,4 3.469,4.156 0.99,0.156 10 false ECU-IG1 NO. 1 2.583,3.604 3.479,3.781 0.896,0.177 10 false ECU-B NO. 1 4.688,3.615 5,3.781 0.313,0.167 10 false ESS 3.448,3.76 3.583,3.927 0.135,0.167 10 false 4 4.531,3.083 4.646,3.24 0.115,0.156 10 false 2 3.969,3.083 4.083,3.24 0.115,0.156 10 false 3 5.031,3.521 5.146,3.667 0.115,0.146 10 false 1 3.604,4.073 3.844,4.24 0.24,0.167 10 false I30 5.896,2.813 7.083,3.24 1.188,0.427 10 false Combination Meter Assembly 4.906,0.563 6.958,0.844 2.052,0.281 10 false CAN Junction RH1 Connector 0.781,2.802 1.146,2.948 0.365,0.146 10 false ECM 0.115,0.115 1.5,0.51 1.385,0.396 12 false V Bus: 3.448,3.375 3.583,3.542 0.135,0.167 10 false 5 3.604,3.479 3.948,3.656 0.344,0.177 10 false BAT 5.625,2.813 5.938,2.969 0.313,0.156 10 false I18 0.469,2.802 0.781,2.958 0.313,0.156 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (STEERING SENSOR BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C156493C39
0.542,2.281 0.865,2.542 0.323,0.26 1.219,3.219 1.531,3.219 1.531,3.219 1.531,2.698 false 2.042,3.219 1.729,3.219 1.729,3.219 1.729,2.698 false 0.281,0.24 0.479,0.438 0.198,0.198 10 false *a 0.708,3.135 1.094,3.292 0.385,0.156 10 false CANL 2.083,3.135 2.5,3.292 0.417,0.156 10 false CANH 0.615,2.323 0.896,2.5 0.281,0.177 10 false I30
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I30-3 (CANH) - I30-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (STEERING SENSOR)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C156493C40
0.594,2.219 0.927,2.479 0.333,0.26 1.031,3.208 1.344,3.208 1.344,3.208 1.344,2.698 false 0.281,0.219 0.479,0.417 0.198,0.198 10 false *a 0.656,3.104 1.167,3.323 0.51,0.219 10 false ESS 0.677,2.25 0.958,2.427 0.281,0.177 10 false I30
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I30-1 (ESS) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
C156493C41
0.5,2.156 0.792,2.406 0.292,0.25 2.219,3.208 1.906,3.208 1.906,3.208 1.906,2.688 false 2.156,2.625 2.521,2.625 false 0.146,0.198 0.417,0.542 0.271,0.344 10 false *a 2.302,3.104 2.667,3.333 0.365,0.229 10 false IG 0.563,2.188 0.844,2.365 0.281,0.177 10 false I30 2.604,2.51 2.99,2.802 0.385,0.292 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I30-4 (IG) - Body ground Power switch on (IG) 11 to 14 V
I30-5 (BAT) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)