Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Power steering ECU assembly branch line or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C252896E11
4.344,1.26 4.521,0.917 4.521,0.917 4.677,0.917 false 2.042,2.75 1.885,3.75 1.885,3.75 1.677,3.75 false 4.896,3.5 5.021,3.677 0.125,0.177 10 false 2 4.271,3.708 4.729,3.896 0.458,0.188 10 false PGND 3.469,3.698 3.667,3.875 0.198,0.177 10 false IG 1.365,4.958 3.26,5.188 1.896,0.229 10 false : CAN Main Bus Line (CANH) 1.365,5.375 3.26,5.604 1.896,0.229 10 false : CAN Main Bus Line (CANL) 4.344,4.948 6.063,5.177 1.719,0.229 10 false : CAN Branch Line (CANH) 4.344,5.354 6.042,5.583 1.698,0.229 10 false : CAN Branch Line (CANL) 5.604,3.927 6.552,4.156 0.948,0.229 10 false Trouble Area 3.615,3.344 4.042,3.49 0.427,0.146 10 false CANH 4.104,3.344 4.51,3.49 0.406,0.146 10 false CANL 3.521,3.135 3.646,3.292 0.125,0.156 10 false 4 3.177,3.49 3.292,3.667 0.115,0.177 10 false 1 4.448,3.135 4.594,3.292 0.146,0.156 10 false 8 0.469,3.667 1.656,4 1.188,0.333 10 false CAN Junction RH1 Connector 4.74,0.833 6.677,1.01 1.938,0.177 10 false CAN Junction LH1 Connector 2.417,3.833 3.01,4.031 0.594,0.198 10 false EPS-IG1 0.74,2.167 1.188,2.313 0.448,0.146 10 false 120 Ω 6.156,2.167 6.604,2.313 0.448,0.146 10 false 120 Ω 2.135,0.49 2.531,0.656 0.396,0.167 10 false DLC3 0.323,2.781 1.552,3.135 1.229,0.354 10 false Combination Meter Assembly 6.271,2.813 6.635,2.958 0.365,0.146 10 false ECM 3.802,3.125 3.958,3.323 0.156,0.198 10 false j3 4.198,3.125 4.354,3.302 0.156,0.177 10 false j3 0.135,0.115 0.719,0.354 0.583,0.24 12 false V Bus: 3.177,3.698 3.323,3.875 0.146,0.177 10 false j3 4.906,3.688 5.052,3.875 0.146,0.188 10 false j2 0.073,2.781 0.385,2.938 0.313,0.156 10 false I18 5.969,2.813 6.281,2.969 0.313,0.156 10 false A25 3.135,4.333 5.083,4.51 1.948,0.177 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the power steering ECU assembly connector.


c.
C259931C01
0.74,1.958 1.156,2.219 0.417,0.26 1.917,2.104 2.333,1.688 false 1.917,2.344 2.323,2.563 false 0,0 0.313,0.156 0.313,0.156 10 false *a 0.896,1.99 1.208,2.188 0.313,0.198 10 false j3 2.375,1.51 2.906,1.708 0.531,0.198 10 false CANH 2.375,2.51 2.906,2.708 0.531,0.198 10 false CANL
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j3-4 (CANH) - j3-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the power steering ECU assembly connector.


b.
C240535C13
0.156,1.531 0.646,1.823 0.49,0.292 2.281,1.688 2.281,0.74 2.281,0.74 2.5,0.74 false 0.115,0.167 0.427,0.521 0.313,0.354 10 false *a 2.594,0.656 3.219,0.917 0.625,0.26 10 false PGND 0.354,1.573 0.542,1.75 0.188,0.177 10 false j2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j2-2 (PGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.
C259931C04
0.74,1.958 1.156,2.219 0.417,0.26 1.469,2.104 1.104,1.542 false 0,0 0.313,0.156 0.313,0.156 10 false *a 0.896,1.99 1.208,2.188 0.313,0.198 10 false j3 0.917,1.469 1.448,1.667 0.531,0.198 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j3-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)