Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Airbag sensor assembly branch line or connector

·

Power source circuit of airbag sensor assembly

·

Airbag sensor assembly ground circuit

·

Airbag sensor assembly



WIRING DIAGRAM

C252909E04
4.406,1.26 4.646,0.927 4.646,0.927 4.813,0.927 false 2.646,1.26 3.167,0.656 3.167,0.656 3.302,0.656 false 2.135,0.542 2.656,0.844 0.521,0.302 10 false DLC3 3.458,4.563 4.396,4.854 0.938,0.292 10 false Trouble Area 0.344,2.813 1.521,3.417 1.177,0.604 10 false Combination Meter Assembly 3.427,0.552 5.385,0.771 1.958,0.219 10 false CAN Junction RH1 Connector 3.406,4.135 5.052,4.385 1.646,0.25 10 false Airbag Sensor Assembly 2.313,3.75 2.729,4.125 0.417,0.375 10 false A/B 3.594,3.281 4.167,3.531 0.573,0.25 10 false CANH 4.063,3.281 4.542,3.563 0.479,0.281 10 false CANL 3.385,3.604 3.75,3.896 0.365,0.292 10 false IG2 4.51,3.385 4.781,3.646 0.271,0.26 10 false E1 4.51,3.76 4.792,4.021 0.281,0.26 10 false E2 3.615,3.063 3.844,3.292 0.229,0.229 10 false 13 4.302,3.052 4.573,3.344 0.271,0.292 10 false 22 6.177,2.24 6.677,2.563 0.5,0.323 10 false 120 Ω 0.667,2.229 1.156,2.542 0.49,0.313 10 false 120 Ω 1.438,4.958 3.354,5.292 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.438,5.344 3.354,5.677 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.385,4.958 6.135,5.292 1.75,0.333 10 false : CAN Branch Line (CANH) 4.385,5.365 6.094,5.698 1.708,0.333 10 false : CAN Branch Line (CANL) 3.125,3.469 3.385,3.729 0.26,0.26 10 false 21 4.792,3.281 5.021,3.552 0.229,0.271 10 false 25 4.802,3.656 5.063,3.906 0.26,0.25 10 false 26 4.906,0.823 6.885,1.01 1.979,0.188 10 false CAN Junction LH1 Connector 3.125,4.135 3.51,4.396 0.385,0.26 10 false I47 6.281,2.823 6.792,3.156 0.51,0.333 10 false ECM 0.25,0.177 0.979,0.594 0.729,0.417 12 false V Bus: 0.083,2.813 0.469,3.063 0.385,0.25 10 false I18 5.958,2.823 6.323,3.063 0.365,0.24 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIRBAG SENSOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the airbag sensor assembly connector.


c.
C188243C32
0.333,1.958 0.719,2.219 0.385,0.26 1.333,2.365 1.135,2.802 1.135,2.802 1.042,2.802 false 1.448,2.115 1.698,2.792 1.698,2.792 1.802,2.792 false 0.167,0.146 2.521,0.49 2.354,0.344 10 *a 1.865,2.719 2.323,2.875 0.458,0.156 10 CANH 0.688,2.729 1.146,2.885 0.458,0.156 10 CANL 0.427,2 0.74,2.156 0.313,0.156 10 I47
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-13 (CANH) - I47-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C188243C33
1.552,1.021 1.938,1.281 0.385,0.26 1.771,2.365 1.979,2.865 1.979,2.865 2.073,2.865 false 1.656,2.354 1.469,2.833 1.469,2.833 1.375,2.833 false 1.208,2.375 0.833,2.813 0.833,2.813 0.74,2.813 false 0.167,0.146 2.521,0.49 2.354,0.344 10 false *a 1.156,2.75 1.448,3 0.292,0.25 10 false E1 1.646,1.073 1.979,1.229 0.333,0.156 10 false I47 0.469,2.719 0.854,2.948 0.385,0.229 10 false IG2 2.167,2.771 2.531,3.021 0.365,0.25 10 false E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I47-25 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
I47-26 (E2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I47-21 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)