Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.02–2014.05
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in One Side of CAN Branch Line  


DESCRIPTION

If an ECU or sensor is not displayed on the Communication Bus Check screen of the intelligent tester and some ECUs and sensors repeatedly appear and disappear from the screen when the CAN main bus lines are normal (there is no open, short, short to +B or short to GND in the main bus lines), there may be an open circuit in either of one pair of CAN branch lines.

HINT:

If some ECUs and sensors repeatedly appear and disappear from the Communication Bus Check screen, communication between the normal ECUs (sensors) and the intelligent tester may be affected by the incomplete signals that are output from the ECU that has an open circuit in either of its CAN branch lines. In this case, the CAN branch lines for the ECUs and sensors that repeatedly appear and disappear from the screen are normal and the ECU that is not displayed on the screen may be the main cause of the problem (this ECU may have an open circuit in either of its CAN branch lines).


Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "Communication Bus Check" screen. One side of CAN branch line is open, or output signals are incomplete.
·

Power management control ECU

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Combination meter assembly

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Steering sensor

·

Power steering ECU assembly

·

Airbag sensor assembly

·

Air conditioning amplifier assembly

·

Smart key ECU assembly (Certification ECU)

·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2

·

Headlight swivel ECU assembly (AFS ECU)*3



·

*1: for Navigation receiver type

·

*2: for Radio and display type

·

*3: w/ Automatic high beam system


CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds and then drive the vehicle at a speed of 5 km/h (3 mph) or more for at least 11.84 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF V BUS BRANCH LINE
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


b.

Using the intelligent tester, select and perform the communication bus check.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


c.

Observe the screen for approximately 2 minutes to check the ECUs and sensors that are not displayed on the screen and also those that repeatedly appear and disappear from the screen.


d.

Check the applicable communication stop mode for the ECU or sensor that is not displayed on the screen.


Result:
Proceed to
NEXT



NEXT

GO TO CORRESPONDING COMMUNICATION STOP MODE