Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Either condition is met:
·

"Certification (Smart)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Smart key ECU assembly (Certification ECU) branch line or connector

·

Power source circuit of smart key ECU assembly (certification ECU)

·

Smart key ECU assembly (Certification ECU) ground circuit

·

Smart key ECU assembly (Certification ECU)



WIRING DIAGRAM

C252908E02
1.708,0.688 1.927,0.688 1.927,0.688 2.24,1.281 false 3.865,1.281 4.167,0.688 4.167,0.688 4.323,0.688 false 3.25,0.563 3.74,0.833 0.49,0.271 10 false DLC3 3.656,4.604 4.625,4.927 0.969,0.323 10 false Trouble Area 0.865,2.823 1.344,3.156 0.479,0.333 10 false ECM 0.51,0.583 1.667,1.073 1.156,0.49 10 false CAN Junction LH1 Connector 6.229,2.219 6.74,2.51 0.51,0.292 10 false 120 Ω 0.677,2.208 1.208,2.5 0.531,0.292 10 false 120 Ω 1.448,4.969 3.417,5.302 1.969,0.333 10 false : CAN Main Bus Line (CANH) 1.438,5.396 3.479,5.729 2.042,0.333 10 false : CAN Main Bus Line (CANL) 4.427,4.979 6.208,5.313 1.781,0.333 10 false : CAN Branch Line (CANH) 4.417,5.385 6.24,5.719 1.823,0.333 10 false : CAN Branch Line (CANL) 2.958,4.188 5.896,4.5 2.938,0.313 10 false Smart Key ECU Assembly (Certification ECU) 3.99,3.271 4.521,3.469 0.531,0.198 10 false CANH 4.458,3.271 4.927,3.458 0.469,0.188 10 false CANL 3.74,3.458 4.063,3.698 0.323,0.24 10 false +B 3.75,3.813 4.021,4.042 0.271,0.229 10 false IG 4.979,3.604 5.167,3.833 0.188,0.229 10 false E 3.906,3.073 4.125,3.292 0.219,0.219 10 false 1 4.865,3.073 5.094,3.313 0.229,0.24 10 false 2 5.25,3.417 5.448,3.646 0.198,0.229 10 false 1 3.51,3.281 3.74,3.521 0.229,0.24 10 false 5 3.458,3.646 3.708,3.875 0.25,0.229 10 false 16 2.521,3.635 3.135,3.896 0.615,0.26 10 false SMART 2.448,3.979 3.531,4.302 1.083,0.323 10 false ECU-IG2 NO. 2 4.448,0.583 6.604,0.896 2.156,0.313 10 false CAN Junction RH1 Connector 0.115,0.115 0.875,0.479 0.76,0.365 12 false V Bus: 5.906,2.844 7.094,3.354 1.188,0.51 10 false Combination Meter Assembly 5.615,2.833 5.979,3.115 0.365,0.281 10 false I18 0.49,2.823 0.896,3.135 0.406,0.313 10 false A25 5.208,3.604 5.542,3.813 0.333,0.208 10 false I86 4.135,3.094 4.469,3.302 0.333,0.208 10 false I87 4.542,3.083 4.875,3.292 0.333,0.208 10 false I87 3.458,3.813 3.792,4.021 0.333,0.208 10 false I87 3.458,3.469 3.792,3.677 0.333,0.208 10 false I87

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the smart key ECU assembly (certification ECU) connector.


c.
C250553C03
0.26,1.281 0.594,1.531 0.333,0.25 2.01,0.74 2.188,0.74 2.188,0.74 2.188,1.385 false 2.417,0.74 2.302,0.74 2.302,0.74 2.302,1.375 false 2.51,0.646 3.052,0.906 0.542,0.26 10 false CANH 1.604,0.646 2.083,0.896 0.479,0.25 10 false CANL 0.25,0.281 0.635,0.552 0.385,0.271 10 false *a 0.323,1.313 0.563,1.51 0.24,0.198 10 false I87
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-1 (CANH) - I87-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SMART KEY ECU ASSEMBLY (CERTIFICATION ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C250554C02
0.281,1.26 0.635,1.552 0.354,0.292 2.542,0.729 2.344,0.729 2.344,0.729 2.344,1.396 false 2.635,0.646 2.906,0.938 0.271,0.292 10 false E 0.177,0.188 0.479,0.458 0.302,0.271 10 false *a 0.354,1.313 0.594,1.521 0.24,0.208 10 false I86
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I86-1 (E) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
C250553C04
0.25,1.281 0.615,1.573 0.365,0.292 0.917,0.74 1.083,0.74 1.083,0.74 1.083,1.385 false 0.948,2.208 1.083,2.208 1.083,2.208 1.083,1.646 false 0.76,2.125 1.219,2.448 0.458,0.323 10 false IG 0.656,0.646 1.031,0.927 0.375,0.281 10 false +B 0.135,0.219 0.552,0.615 0.417,0.396 10 false *a 0.323,1.344 0.563,1.542 0.24,0.198 10 false I87
*a Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I87-5 (+B) - Body ground Power switch off 11 to 14 V
I87-16 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)