Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioning Amplifier" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C252895E12
4.885,2.667 4.969,3.531 4.969,3.531 5.125,3.531 false 3.594,1.146 3.521,0.792 3.521,0.792 3.333,0.792 false 5.896,2.688 7.115,3.073 1.219,0.385 10 false Combination Meter Assembly 1.417,5 3.313,5.323 1.896,0.323 10 false : CAN Main Bus Line (CANH) 4.385,4.99 6.083,5.313 1.698,0.323 10 false : CAN Branch Line (CANH) 4.385,5.406 6.135,5.729 1.75,0.323 10 false : CAN Branch Line (CANL) 1.417,5.417 3.313,5.74 1.896,0.323 10 false : CAN Main Bus Line (CANL) 2.365,3.938 4.604,4.135 2.24,0.198 10 false Air Conditioning Amplifier Assembly 2.615,3.219 2.906,3.417 0.292,0.198 10 false IG+ 2.885,3.135 3.292,3.313 0.406,0.177 10 false CANH 3.365,3.135 3.75,3.313 0.385,0.177 10 false CANL 3.688,3.417 4.031,3.594 0.344,0.177 10 false GND 1.479,3.333 2.021,3.51 0.542,0.177 10 false A/C-IG1 2.469,3.115 2.604,3.292 0.135,0.177 10 false 1 4.063,3.323 4.26,3.5 0.198,0.177 10 false 14 2.927,2.958 3.104,3.135 0.177,0.177 10 false 11 3.542,2.958 3.74,3.135 0.198,0.177 10 false 12 4.427,0.427 4.802,0.604 0.375,0.177 10 false DLC3 1.49,0.698 3.427,0.917 1.938,0.219 10 false CAN Junction LH1 Connector 2.646,4.469 3.76,4.854 1.115,0.385 10 false Trouble Area 0.677,2.094 1.073,2.271 0.396,0.177 10 false 120 Ω 6.177,2.125 6.573,2.302 0.396,0.177 10 false 120 Ω 5.177,3.458 6.427,3.844 1.25,0.385 10 false CAN Junction RH1 Connector 2.115,3.938 2.458,4.115 0.344,0.177 10 false I77 0.76,2.688 1.125,2.833 0.365,0.146 10 false ECM 0.156,0.146 1.5,0.417 1.344,0.271 12 false V Bus: 2.406,3.563 2.604,3.74 0.198,0.177 10 false 21 2.625,3.646 2.823,3.823 0.198,0.177 10 false B 1.521,3.771 1.938,3.948 0.417,0.177 10 false A/C-B 5.615,2.698 5.927,2.854 0.313,0.156 10 false I18 0.448,2.688 0.76,2.844 0.313,0.156 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.


c.
C240533C01
0.396,1.135 0.885,1.427 0.49,0.292 1.458,0.656 1.802,0.656 1.802,0.656 1.802,2.125 false 2.24,0.635 1.917,0.635 1.917,0.635 1.917,2.115 false 0.156,0.146 0.354,0.354 0.198,0.208 10 false *a 0.927,0.573 1.385,0.771 0.458,0.198 10 false CANH 2.302,0.531 2.865,0.75 0.563,0.219 10 false CANL 0.542,1.198 0.823,1.375 0.281,0.177 10 false I77
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-11 (CANH) - I77-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C240533C07
0.99,0.625 1.385,0.906 0.396,0.281 2.479,1.25 2.156,1.25 2.156,1.25 2.156,2.125 false 0.646,2.115 0.646,1.354 0.646,1.354 0.802,1.354 false 0.917,2.854 0.646,2.854 0.646,2.854 0.646,2.365 false 0.156,0.146 0.354,0.354 0.198,0.208 10 false *a 2.542,1.146 3.073,1.427 0.531,0.281 10 false GND 1.115,0.677 1.396,0.854 0.281,0.177 10 false I77 0.875,1.26 1.323,1.521 0.448,0.26 10 false IG+ 1,2.771 1.198,3.01 0.198,0.24 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-14 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I77-1 (IG+) - Body ground Power switch on (IG) 11 to 14 V
I77-21 (B) - Body ground Power switch off 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)