Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2012.02–2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  AFS ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
AFS ECU Communication Stop Mode Either condition is met:
·

"Headlight swivel (AFS)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Headlight swivel ECU assembly (AFS ECU) branch line or connector

·

Power source circuit of headlight swivel ECU assembly (AFS ECU)

·

Headlight swivel ECU assembly (AFS ECU) ground circuit

·

Headlight swivel ECU assembly (AFS ECU)



WIRING DIAGRAM

C252894E11
1.656,0.677 1.885,0.677 1.885,0.677 2.135,1.156 false 3.823,1.156 4.052,0.677 4.052,0.677 4.208,0.677 false 2.99,0.448 3.469,0.75 0.479,0.302 10 false DLC3 5.792,3.75 6.802,4.104 1.01,0.354 10 false Trouble Area 0.854,2.719 1.281,2.917 0.427,0.198 10 false ECM 5.781,2.719 6.948,3.313 1.167,0.594 10 false Combination Meter Assembly 0.469,0.583 1.625,1.031 1.156,0.448 10 false CAN Junction RH1 Connector 6.146,2.104 6.604,2.385 0.458,0.281 10 false 120 Ω 0.708,2.104 1.219,2.479 0.51,0.375 10 false 120 Ω 1.458,4.979 3.375,5.302 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.458,5.396 3.375,5.719 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.438,4.979 6.219,5.302 1.781,0.323 10 false : CAN Branch Line (CANH) 4.438,5.385 6.135,5.708 1.698,0.323 10 false : CAN Branch Line (CANL) 3.385,4.094 5.354,4.531 1.969,0.438 10 false Headlight Swivel ECU Assembly (AFS ECU) 3.781,3.292 4.323,3.646 0.542,0.354 10 false MPX1 4.219,3.292 4.75,3.573 0.531,0.281 10 false MPX2 3.781,3.073 4,3.313 0.219,0.24 10 false 12 4.427,3.073 4.656,3.302 0.229,0.229 10 false 13 4.281,0.583 6.271,0.813 1.99,0.229 10 false CAN Junction LH1 Connector 3.073,4.083 3.469,4.354 0.396,0.271 10 false A35 2.51,3.75 3.313,4.156 0.802,0.406 10 false H-LP LVL 3.521,3.552 3.865,3.813 0.344,0.26 10 false IG 3.271,3.458 3.573,3.729 0.302,0.271 10 false 15 4.948,3.448 5.281,3.75 0.333,0.302 10 false 22 4.677,3.563 5.042,3.844 0.365,0.281 10 false E1 0.146,0.125 0.833,0.458 0.688,0.333 12 false V Bus: 5.521,2.719 5.885,2.948 0.365,0.229 10 false I18 0.51,2.719 0.875,2.938 0.365,0.219 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AFS ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A35 headlight swivel ECU assembly (AFS ECU) connector.


c.
C188285C26
1.667,2.667 1.99,2.896 0.323,0.229 2.375,1.302 2.604,1.302 2.604,1.302 2.927,1.927 false 2.354,1.063 2.625,1.063 2.625,1.063 3.083,1.927 false 0.083,0.083 0.396,0.323 0.313,0.24 10 *a 1.719,2.698 2.177,2.896 0.458,0.198 10 A35 1.958,0.969 2.417,1.167 0.458,0.198 10 MPX2 1.969,1.219 2.427,1.417 0.458,0.198 10 MPX1
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly (AFS ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
A35-12 (MPX1) - A35-13 (MPX2) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY (AFS ECU))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C188285C27
1.667,1.177 1.99,1.406 0.323,0.229 1.573,2.25 1.792,3.01 1.792,3.01 1.896,3.01 false 0.083,0.083 0.396,0.323 0.313,0.24 10 *a 1.708,1.208 2.167,1.406 0.458,0.198 10 A35 1.958,2.927 2.417,3.125 0.458,0.198 10 E1
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly (AFS ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
A35-22 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
C188285C28
1.667,1.177 1.99,1.406 0.323,0.229 0.521,2.25 1.115,3.01 1.115,3.01 1.208,3.01 false 0.083,0.083 0.396,0.323 0.313,0.24 10 false *a 1.708,1.208 2.167,1.406 0.458,0.198 10 false A35 1.26,2.927 1.719,3.125 0.458,0.198 10 false IG
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly (AFS ECU))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Value
A35-15 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (AFS ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)