Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Radio and display receiver assembly branch line or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C252910E15
4.365,0.438 4.115,0.438 4.115,0.438 3.656,1.146 false 2.063,0.708 2.219,0.708 2.219,0.708 2.427,1.135 false 2.708,0.427 3.271,0.76 0.563,0.333 10 false DLC3 5.74,3.875 6.625,4.219 0.885,0.344 10 false Trouble Area 0.354,2.677 1.531,3.188 1.177,0.51 10 false Combination Meter Assembly 4.469,0.333 6.708,0.646 2.24,0.313 10 false CAN Junction LH1 Connector 6.188,2.083 6.729,2.396 0.542,0.313 10 false 120 Ω 0.688,2.104 1.156,2.354 0.469,0.25 10 false 120 Ω 1.469,5.125 3.385,5.458 1.917,0.333 10 false : CAN Main Bus Line (CANH) 1.469,5.417 3.385,5.75 1.917,0.333 10 false : CAN Main Bus Line (CANL) 4.458,5.125 6.219,5.458 1.76,0.333 10 false : CAN Branch Line (CANH) 4.458,5.417 6.146,5.75 1.688,0.333 10 false : CAN Branch Line (CANL) 3.844,3.135 4.396,3.375 0.552,0.24 10 false CANH 4.302,3.135 4.833,3.396 0.531,0.26 10 false CANL 3.531,3.5 3.802,3.74 0.271,0.24 10 false IG 3.531,4.167 4.094,4.406 0.563,0.24 10 false ACC1 4.521,3.469 5.063,3.813 0.542,0.344 10 false GND1 3.854,2.708 4.073,2.969 0.219,0.26 10 false 9 4.438,2.708 4.75,2.927 0.313,0.219 10 false 10 5.063,3.26 5.26,3.552 0.198,0.292 10 false 7 2.365,3.677 2.938,4.094 0.573,0.417 10 false ECU-IG1 NO. 2 2.354,3.281 3.031,3.49 0.677,0.208 10 false RADIO-B 2.375,4.354 3.229,4.646 0.854,0.292 10 false ECU-ACC 0.198,0.594 2.177,0.896 1.979,0.302 10 false CAN Junction RH1 Connector 3.177,4.5 5.719,4.75 2.542,0.25 10 false Radio and Display Receiver Assembly 3.177,3.521 3.573,3.76 0.396,0.24 10 false I155 6.292,2.698 6.729,2.948 0.438,0.25 10 false ECM 3.875,2.927 4.333,3.198 0.458,0.271 10 false I155 4.281,2.927 4.719,3.156 0.438,0.229 10 false I155 3.188,4.177 3.552,4.365 0.365,0.188 10 false I152 4.99,3.479 5.438,3.75 0.448,0.271 10 false I152 3.26,3.323 3.417,3.51 0.156,0.188 10 false 1 3.271,3.979 3.448,4.198 0.177,0.219 10 false 3 0.198,0.115 1.271,0.542 1.073,0.427 12 false V Bus: 3.51,3.135 3.865,3.385 0.354,0.25 10 false +B1 3.177,3.135 3.563,3.354 0.385,0.219 10 false I152 3.271,2.938 3.438,3.146 0.167,0.208 10 false 4 0.104,2.667 0.5,2.979 0.396,0.313 10 false I18 5.958,2.698 6.354,2.958 0.396,0.26 10 false A25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the radio and display receiver assembly connector.


c.
C240580C03
0.323,1.083 0.781,1.365 0.458,0.281 1.542,0.573 1.792,0.573 1.792,0.573 1.792,1.896 false 2.115,0.563 1.896,0.563 1.896,0.563 1.896,1.896 false 0.135,0.135 0.344,0.323 0.208,0.188 10 false *a 2.188,0.458 2.708,0.719 0.521,0.26 10 false CANL 1.104,0.479 1.594,0.719 0.49,0.24 10 false CANH 0.406,1.135 0.729,1.302 0.323,0.167 10 false I155
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-9 (CANH) - I155-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the radio and display receiver assembly connector.


b.
C241290C07
0.365,3.458 0.792,3.719 0.427,0.26 0.135,1.51 0.563,1.792 0.427,0.281 2.448,3.573 2.031,3.573 false 0.792,1.656 0.792,1.021 0.792,1.021 0.615,1.021 false 1.802,3.51 1.802,2.76 1.802,2.76 2.094,2.76 false 1.448,3.844 1.448,4.188 1.448,4.188 1.167,4.188 false 2.177,2.698 2.875,3.146 0.698,0.448 10 false ACC1 2.521,3.479 3,3.865 0.479,0.385 10 false +B1 0.396,0.948 0.656,1.229 0.26,0.281 10 false IG 0.74,4.094 1.438,4.385 0.698,0.292 10 false GND1 0.448,3.5 0.896,3.833 0.448,0.333 10 false I152 0.219,1.563 0.49,1.74 0.271,0.177 10 false I155 0.146,0.135 0.51,0.521 0.365,0.385 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I152-7 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I152-3 (ACC1) - Body ground Power switch on (ACC) 11 to 14 V
I152-4 (+B1) - Body ground Power switch off 11 to 14 V
I155-1 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)