Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075053 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the front door outside handle assembly (for driver door) (lock sensor) (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [lock sensor]).

WIRING DIAGRAM

B281953
1.292,0.729 1.844,1.063 0.552,0.333 10 false ANT1 1.271,1.177 2.021,1.573 0.75,0.396 10 false ANT2 0.313,3.448 0.865,3.802 0.552,0.354 10 false V1 1.344,3.052 1.76,3.313 0.417,0.26 10 false GND 1.771,1.083 2.198,1.479 0.427,0.396 10 false 3 1.781,2.927 2.094,3.302 0.313,0.375 10 false 2 1.771,0.625 2.208,1.063 0.438,0.438 10 false 6 5.75,0.719 6.167,0.885 0.417,0.167 10 false CLG1 5.75,1.198 6.177,1.354 0.427,0.156 10 false CG1B 5.75,3.031 5.969,3.271 0.219,0.24 10 false E 5.469,0.563 5.635,0.719 0.167,0.156 10 false 5 5.417,0.719 5.656,0.875 0.24,0.156 10 false I86 5.417,1.177 5.656,1.333 0.24,0.156 10 false I86 5.417,1.635 5.656,1.792 0.24,0.156 10 false I86 5.417,2.104 5.656,2.26 0.24,0.156 10 false I86 5.417,3.021 5.656,3.177 0.24,0.156 10 false I86 5.417,2.563 5.656,2.719 0.24,0.156 10 false I87 5.469,1 5.646,1.167 0.177,0.167 10 false 4 1.531,1.656 1.781,1.917 0.25,0.26 10 false B 1.271,2.115 1.885,2.406 0.615,0.292 10 false SENS 1.771,2 2.021,2.281 0.25,0.281 10 false 4 1.771,1.542 2.104,1.854 0.333,0.313 10 false 5 5.75,1.646 6.167,1.813 0.417,0.167 10 false POS1 5.75,2.115 6.177,2.271 0.427,0.156 10 false SEN1 5.438,1.458 5.615,1.615 0.177,0.156 10 false 15 5.469,1.927 5.625,2.094 0.156,0.167 10 false 3 1.281,2.573 1.958,2.938 0.677,0.365 10 false TRG+ 1.771,2.458 2.073,2.75 0.302,0.292 10 false 1 5.75,2.583 6.427,2.927 0.677,0.344 10 false TSW1 5.469,2.375 5.729,2.635 0.26,0.26 10 false 7 5.469,2.844 5.625,3.01 0.156,0.167 10 false 1 5.365,3.531 6.99,3.896 1.625,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.313,3.615 2.042,3.99 1.729,0.375 10 false Front Door Outside Handle Assembly (for Driver Door)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assembles in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM

2.READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D-Door Trigger Switch Driver door touch sensor (lock sensor) ON or OFF ON: Driver door touch sensor (lock sensor) touched
OFF: Driver door touch sensor (lock sensor) not touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
D-Door Trigger Switch
50003 125 12
OK:

The intelligent tester display changes correctly in response to the operation of the front door outside handle assembly (for driver door).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the V1 front door outside handle assembly (for driver door) connector.


b.

Disconnect the I87 and I86 certification ECU (smart key ECU assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V1-1 (TRG+) - I87-7 (TSW1) Always Below 1 Ω
I86-1 (E) - Body ground Always Below 1 Ω
V1-1 (TRG+) or I87-7 (TSW1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR LOCK SENSOR SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR LOCK SENSOR SIGNAL INPUT)
a.

Connect the V1 front door outside handle assembly (for driver door) connector.

B282015
2.115,0.823 2.49,1.052 0.375,0.229 4.802,0.823 5.177,1.052 0.375,0.229 3.552,0.823 3.927,1.052 0.375,0.229 5.5,1.51 5.667,2.073 false 4.177,1.646 4.333,2.083 false 5.021,3.271 5.5,2.938 5.5,2.938 5.333,3.271 false 0.917,0.563 1.083,0.719 0.167,0.156 10 false *a 4.167,2.781 4.333,2.938 0.167,0.156 10 false *1 4.021,3.854 4.375,4.01 0.354,0.156 10 false GND 5.667,2.115 5.833,2.271 0.167,0.156 10 false E 5.479,2.781 5.646,2.938 0.167,0.156 10 false *b 2.219,0.865 2.542,1.031 0.323,0.167 10 false O2 4.906,0.865 5.229,1.031 0.323,0.167 10 false I86 4.146,2.115 4.573,2.271 0.427,0.156 10 false TSW1 3.656,0.865 3.979,1.031 0.323,0.167 10 false I87
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b In actuality, sampling is being performed



b.

Connect the I87 and I86 certification ECU (smart key ECU assembly) connectors.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
I87-7 (TSW1) - I86-1 (E) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)