Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM2040EQ _59 Vehicle Exterior _014735 DOOR / HATCH _0075151 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69283 4.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B286883

Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.


Hide 67491A 5.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B286884

Disengage the 3 clips and remove the front door lower frame bracket garnish.


Hide 6.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B307002

Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.


b.

Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 7.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B286886

Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.


b.

Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.


Hide 74210 8.REMOVE FRONT ARMREST ASSEMBLY

a.
B286887

Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.


Hide 81911B 9.REMOVE REFLEX REFLECTOR

a.
B293479C01
2.063,1.271 2.063,1.771 false 2.094,3.74 2.094,4.24 false 1.969,1.781 2.156,1.979 0.188,0.198 10 false *1 2,4.25 2.188,4.448 0.188,0.198 10 false *1 0.156,0.094 0.417,0.323 0.26,0.229 12 false *A 0.156,2.396 0.417,2.625 0.26,0.229 12 false *B
*A for LH Side
*B for RH Side
*1 Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the reflex reflector.


Hide 67601 10.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B286888C02
1.286,0.196 1.452,0.36 0.166,0.164 10 *1 1.47,0.284 1.781,0.292 false
*1 Protective Tape


Put protective tape around the front door panel.


b.
B314410

Remove the 3 screws.


c.

Using a clip remover, disengage the 10 clips.


d.
B314411C01
2.827,4.121 2.978,4.276 0.151,0.155 10 *1 2.506,4.22 2.8,4.2 false 2.44,0.351 2.609,0.511 0.169,0.160 10 *2 2.012,0.488 2.407,0.443 false
*1 Reference Boss
*2 Front Door Inner Glass Weatherstrip


Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.


e.

Disengage the reference boss from the front door panel.


f.

Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.


g.
B286891

Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


Hide 69205 11.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B286892

Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.


Hide 68171B 12.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B286893C02
0.208,0.991 0.375,1.143 0.167,0.152 10 *1 0.29,0.99 0.339,0.845 false
*1 Screwdriver


Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.


Hide 84927 13.REMOVE SEAT MEMORY SWITCH (w/ Memory)

Hide 86160 14.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 15.REMOVE MIRROR SUB-ASSEMBLY WITH COVER

Hide 89430 16.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 67831 17.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B314409

Disconnect each connector.


b.

Disengage the 3 clamps.


c.

Remove the front door service hole cover.

HINT:

Remove any remaining butyl tape from the door.



Hide 68101 18.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B307947

Remove the grommet.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Disconnect the power window regulator master switch assembly.


f.
B307948

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the door glass to fall.



g.
B307949E02
2.729,0.281 2.927,0.469 0.198,0.188 10 false (1) 1.917,0.115 2.115,0.302 0.198,0.188 10 false (2)

Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 19.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B307950C01
1.542,0.823 2.427,0.177 false 2.438,0.063 2.583,0.219 0.146,0.156 10 false *1
*1 Temporary Bolt


Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.



b.

Remove the 5 bolts.


c.

Remove the front door window regulator assembly.


d.

Remove the temporary bolt from the front door window regulator assembly.


Hide 85710E 20.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B286899

Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.


Hide 67923 21.REMOVE NO. 1 FRONT DOOR STIFFENER CUSHION

a.
B286900C03
2.051,1.204 2.221,1.364 0.169,0.16 10 *1 1.153,1.295 2.035,1.295 false
*1 Double-sided Tape


Remove the 2 bolts.


b.

Disengage the 2 guides and remove the No. 1 front door stiffener cushion.


Hide 68141C 22.REMOVE FRONT DOOR GLASS RUN

a.
B307951

Remove the front door glass run.


Hide 67401F 23.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B286902

Remove the 2 bolts.


b.

Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.


Hide 67403F 24.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B307952

Remove the 2 bolts.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B286904

Remove the hole plug.


b.
B307953

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69250B 26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B286906

Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.


Hide 69217F 27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B286907

Remove the hole plug.


b.
B307954

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69220 28.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B288527

Disengage the 2 claws.


b.

Using a screwdriver, disconnect the connector.


c.
B307955

Remove the front door outside handle assembly as shown in the illustration.


Hide 69241H 29.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B307956

Disengage the 3 claws and remove the front door front outside handle pad.


Hide 69242E 30.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B307957

Disengage the 2 claws and remove the front door rear outside handle pad.


Hide 69030A 31.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B286913C04
0.148,2.736 0.306,2.899 0.159,0.163 10 *1 0.463,2.612 0.308,2.759 false
*1 Front Door Lock Open Rod


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.


c.

When reusing the front door lock with motor assembly:

i.
B286914

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69710B 32.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B286915

Remove the front door lock remote control cable assembly.


Hide 69750C 33.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B286916

Using a screwdriver, disengage the 3 claws.


b.
B286917

Remove the front door inside locking cable assembly.


Hide 69201A 34.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B286918

Disconnect the connector.


b.

Disengage the 3 clamps.


c.
B307958C01
2.729,1.531 3.073,1.438 false 0.063,0.01 0.26,0.188 0.198,0.177 10 false *a 0.063,2.104 0.26,2.281 0.198,0.177 10 false *b 3.115,1.365 3.271,1.521 0.156,0.156 10 false *1
*1 Door Handle Nut
*a Outside
*b Inside


Using a T30 "TORX" socket wrench, remove the screw and door handle nut.


d.

Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.


Hide 82185A 35.REMOVE FRONT DOOR SMART WIRE

a.
B286920

Disengage the 3 clamps and remove the front door smart wire.


Hide 69311A 36.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B286921E02
1.24,0.573 1.438,0.76 0.198,0.188 10 true (1) 0.417,0.667 0.615,0.844 0.198,0.177 10 false (2)

Remove the front door lock open rod as indicated by the arrows and in the order shown in the illustration.


Hide 68610B 37.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B286922

Remove the 3 bolts and front door check assembly.


Hide 67861 38.REMOVE FRONT DOOR WEATHERSTRIP

a.
B307959

Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.


Hide 67663D 39.REMOVE DOOR FRAME GARNISH

a.
B286924

Disengage the clip and remove the door frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing it.



Hide 67863B 40.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP

a.
B286925

Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.


Hide 67001A 41.REMOVE FRONT DOOR PANEL CUSHION

a.
B307960

Disengage the 2 claws and remove the 2 front door panel cushions.


Hide 67481C 42.REMOVE FRONT DOOR FRONT LOWER FRAME SEAL

a.
B286927

Remove the front door front lower frame seal.


Hide 75710 43.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL


Hide 75755C 44.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR WINDOW FRAME MOULDING>REMOVAL


Hide 75753 45.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR WINDOW FRAME MOULDING>REMOVAL


Hide 75985B 46.REMOVE FRONT DOOR STRIPE

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>REMOVAL


Hide 75975G 47.REMOVE FRONT DOOR LOWER OUTSIDE STRIPE

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>REMOVAL