If the luggage compartment door entry unlock function does not operate, the request code may not be being transmitted from the luggage compartment door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage)), a luggage compartment door outer switch malfunction or wave interference.
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.
The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the power switch off to troubleshoot:
Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Trunk Open Mode | Luggage door opening switch assembly | ON or OFF | Customization status displayed | - |
| Tester Display |
|---|
| Trunk Open Mode |
| Result | Proceed to |
|---|---|
| Entry luggage compartment door open mode is ON | A |
| Entry luggage compartment door open mode is OFF | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Luggage compartment door opener outer switch | ON or OFF | ON: Luggage compartment door opener outer switch pushed
OFF: Luggage compartment door opener outer switch not pushed |
- |
| Tester Display |
|---|
| Tr/B-Door Unlock SW |
On the intelligent tester screen, the display changes between ON and OFF according to the chart above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Trunk and Back-Door Open | Operate luggage compartment door lock motor | ON/OFF | - |
| Tester Display |
|---|
| Trunk and Back-Door Open |
Luggage compartment door lock motor operates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly near the electrical key antenna (outside luggage), and perform an entry luggage compartment open function check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.
When pressing the luggage compartment door opener outer switch, hold the electrical key transmitter sub-assembly approximately 1 m (3.28 ft.) above the ground and approximately 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.
When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
Entry functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in the key diagnostic mode.
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.
When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.
Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the electrical key transmitter sub-assembly is as shown in the illustration.
If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 1 due to a malfunction, such as wave interference.
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O2 certification ECU (smart key ECU assembly) connector.
Disconnect the T11 electrical key antenna (outside luggage) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O2-1 (CG8B) - T11-2 (CLGB) | Always | Below 1 Ω |
| O2-2 (CLG8) - T11-1 (ANTE8) | Always | Below 1 Ω |
| O2-1 (CG8B) or T11-2 (CLGB) - Body ground | Always | 10 kΩ or higher |
| O2-2 (CLG8) or T11-1 (ANTE8) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Electrical Key Antenna (Outside Luggage)) |
Remove the electrical key antenna (outside luggage).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ANTE8) - 2 (CLGB) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Luggage Compartment Door Lock Assembly) |
| *b | Close (Lock) |
| *c | Open (Unlock) |
Remove the luggage compartment door lock assembly.
Click hereVehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK>REMOVAL
Check the operation of the door lock motor.
Move the door lock to the close (lock) position.
Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.
| Measurement Condition | Specified Condition |
|---|---|
| Auxiliary battery positive (+) → 1 (B)
Auxiliary battery negative (-) → 2 (E) |
Luggage compartment door lock motor open (unlock) operation |
| *a | Component without harness connected
(Luggage Compartment Door Lock Assembly) |
| *b | Close (Lock) |
| *c | Open (Unlock) |
Check the door courtesy light switch.
Move the door lock to the close (lock) position.
Measure the resistance according to the value(s) in the table below.
| Measurement Condition | Door Lock Condition | Specified Condition |
|---|---|---|
| 2 (E) - 3 (D+) | Close (Lock) | 10 kΩ or higher |
| 2 (E) - 3 (D+) | Open (Unlock) | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Luggage compartment door lock motor:
Disconnect the 3C instrument panel junction block assembly connector.
Disconnect the T3 luggage compartment door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T3-2 (E) - Body ground | Always | Below 1 Ω |
| 3C-10 (TR+) - T3-1 (B) | Always | Below 1 Ω |
| 3C-10 (TR+) or T3-1(B) - Body ground | Always | 10 kΩ or higher |
Luggage door courtesy light switch:
Disconnect the 3C instrument panel junction block assembly connector.
Disconnect the T3 luggage compartment door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T3-2 (E) - Body ground | Always | Below 1 Ω |
| 3C-9 (LGCY) - T3-3 (D+) | Always | Below 1 Ω |
| 3C-9 (LGCY) or T3-3 (D+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the instrument panel junction block assembly with a new one.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that the luggage compartment door entry unlock functions operate normally.
Luggage compartment door entry unlock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the luggage door opening switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH>REMOVAL
| *a | Component without harness connected
(Luggage Door Opening Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (E) - 3 (UL) | Luggage door opening switch assembly not pushed | 10 kΩ or higher |
| 2 (E) - 3 (UL) | Luggage door opening switch assembly pushed | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O2 certification ECU (smart key ECU assembly) connector.
Disconnect the T4 luggage door opening switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O2-22 (TSW5) - T4-3 (UL) | Always | Below 1 Ω |
| O2-22 (TSW5) or T4-3 (UL) - Body ground | Always | 10 kΩ or higher |
| T4-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG