Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075053 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B290526E08
4.969,4.167 5.385,4.344 0.417,0.177 10 false CUTB 3.677,4.281 4.542,4.458 0.865,0.177 10 false ECU-B NO. 1 1.875,4.135 3.26,4.313 1.385,0.177 10 false from Auxiliary Battery 3.875,4.698 4.417,4.875 0.542,0.177 10 false SMART 4.625,4.167 4.896,4.344 0.271,0.177 10 false I87 4.688,3.979 4.865,4.156 0.177,0.177 10 false 4 4.969,5.76 5.406,5.938 0.438,0.177 10 false RDAM 4.688,5.594 4.865,5.771 0.177,0.177 10 false 6 4.969,6.146 5.385,6.323 0.417,0.177 10 false CSEL 4.698,5.979 4.875,6.156 0.177,0.177 10 false 7 4.969,6.531 5.385,6.708 0.417,0.177 10 false E 4.656,6.865 6.198,7.177 1.542,0.313 10 false Certification ECU (Smart Key ECU Assembly) 0.5,6.792 0.865,6.969 0.365,0.177 10 false O25 0.5,6.969 1.958,7.146 1.458,0.177 10 false Door Control Receiver 4.688,6.354 4.865,6.531 0.177,0.177 10 false 1 4.969,4.563 5.198,4.74 0.229,0.177 10 false +B 4.698,4.375 4.802,4.552 0.104,0.177 10 false 5 4.969,5.375 5.313,5.552 0.344,0.177 10 false RCO 1.5,5.406 1.729,5.708 0.229,0.302 10 false +5 1.792,5.281 1.969,5.458 0.177,0.177 10 false 4 1.333,5.74 1.729,5.917 0.396,0.177 10 false DATA 1.792,5.656 1.969,5.833 0.177,0.177 10 false 5 1.792,6.031 1.969,6.208 0.177,0.177 10 false 2 1.375,6.458 1.75,6.635 0.375,0.177 10 false GND 1.792,6.365 1.969,6.542 0.177,0.177 10 false 1 4.646,5.198 4.823,5.375 0.177,0.177 10 false 15 4.625,4.563 4.865,4.74 0.24,0.177 10 false I87 4.625,6.531 4.854,6.708 0.229,0.177 10 false I86 4.625,5.375 4.917,5.552 0.292,0.177 10 false O2 4.625,5.76 4.958,5.938 0.333,0.177 10 false O2 4.625,6.146 4.938,6.323 0.313,0.177 10 false O2 1.323,6.115 1.74,6.292 0.417,0.177 10 false CSEL 1.823,4.969 3.219,5.354 1.396,0.385 10 false from IG2 Relay Circuit 4.969,4.969 5.385,5.146 0.417,0.177 10 false IG 4.646,4.771 4.823,4.948 0.177,0.177 10 false 16 4.625,4.969 4.865,5.146 0.24,0.177 10 false I87 1.865,0.677 3.063,0.885 1.198,0.208 10 false to Auxiliary Battery 4.979,2.271 5.406,2.448 0.427,0.177 10 false ACCD 4.979,1.49 5.417,1.667 0.438,0.177 10 false IG1D 4.979,0.688 5.417,0.865 0.438,0.177 10 false AM21 4.688,1.083 5,1.26 0.313,0.177 10 false I3 3.573,0.823 3.99,1 0.417,0.177 10 false AM2 4.688,1.49 5,1.667 0.313,0.177 10 false I4 4.688,0.688 5,0.865 0.313,0.177 10 false I4 4.688,2.271 5,2.448 0.313,0.177 10 false I4 4.615,1.885 4.927,2.063 0.313,0.177 10 false A39 4.979,1.083 5.417,1.26 0.438,0.177 10 false AM22 4.979,1.885 5.417,2.063 0.438,0.177 10 false IG2D 4.719,0.896 4.896,1.052 0.177,0.156 10 false 1 4.708,1.313 4.885,1.469 0.177,0.156 10 false 2 4.729,0.49 4.906,0.646 0.177,0.156 10 false 7 4.698,2.083 4.875,2.24 0.177,0.156 10 false 1 4.708,1.708 4.885,1.865 0.177,0.156 10 false 2 5.583,0.688 5.896,0.865 0.313,0.177 10 false E01 5.563,1.083 5.875,1.26 0.313,0.177 10 false E02 5.625,1.646 5.854,1.823 0.229,0.177 10 false E1 5.573,2.052 5.885,2.229 0.313,0.177 10 false E12 6.01,0.917 6.188,1.073 0.177,0.156 10 false 5 6.01,0.521 6.188,0.677 0.177,0.156 10 false 5 6.01,1.469 6.188,1.625 0.177,0.156 10 false 6 6.01,1.875 6.188,2.031 0.177,0.156 10 false 4 6,1.646 6.313,1.823 0.313,0.177 10 false I3 6,0.688 6.313,0.865 0.313,0.177 10 false I3 6,1.083 6.313,1.26 0.313,0.177 10 false I4 6,2.052 6.313,2.229 0.313,0.177 10 false I4 4.438,2.938 6.552,3.115 2.115,0.177 10 false Power Management Control ECU 0.823,7.438 2.479,7.615 1.656,0.177 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".



PROCEDURE

1.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the vehicle auxiliary battery.

Standard voltage:

11 to 14 V (IG OFF)


HINT:

It may be possible to tell whether the vehicle auxiliary battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the vehicle auxiliary battery before proceeding.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the intelligent tester and check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

When using the intelligent tester with the power switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.


OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

4.CHECK KEY DIAGNOSTIC MODE

NG

4.CHECK KEY DIAGNOSTIC MODE

b.

Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B274829C11
1.278,1.123 1.474,1.303 0.196,0.18 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

ii.
B274816C16
2.418,1.131 2.638,1.31 0.22,0.18 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iii.
B274820C07
2.487,0.278 2.674,0.453 0.187,0.176 10 *a 1.735,1.154 2.279,0.375 2.279,0.375 2.451,0.375 false
*a Inspection Point


Check the No. 1 indoor electrical key antenna (front floor):

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iv.
B274821C07
1.803,0.676 2.43,0.326 2.43,0.326 2.645,0.326 false 2.699,0.229 2.867,0.391 0.168,0.161 10 *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna (rear floor):

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

v.
B274824C06
1.875,1.322 2.053,1.483 0.178,0.162 10 *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
OK:

Wireless door lock buzzer sounds.




Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspection succeeds for only one of the channels C



A

5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

11.CHECK WAVE ENVIRONMENT

C

10.CHECK WAVE ENVIRONMENT
5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

7.CHECK ENTRY DOOR LOCK OPERATION
6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK ENTRY DOOR LOCK OPERATION
7.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

8.CHECK TRANSMITTER BATTERY

NG

11.CHECK WAVE ENVIRONMENT
8.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C


HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid system by holding the electrical key transmitter sub-assembly against the power switch, depressing the brake pedal and pressing the power switch.






A

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

REPLACE TRANSMITTER BATTERY

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery

i.

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT


ii.
B281811C01
1.784,1.051 1.784,0.155 1.784,0.155 2.037,0.155 false 2.08,0.071 2.25,0.239 0.17,0.168 10 *1
*1 Lead Wire


Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B281812C05
1.154,0.694 1.691,0.694 1.691,0.694 2.225,1.09 false 0.935,0.608 1.105,0.768 0.17,0.16 10 *1
*1 GND


Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST



Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Power switch off, all doors closed and lock sensor touched 2.3 to 3.2 V




Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

10.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

20.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
11.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

12.READ VALUE USING INTELLIGENT TESTER (ACC SW, IG SW)
12.READ VALUE USING INTELLIGENT TESTER (ACC SW, IG SW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Power switch status ON or OFF ON: Power switch on (ACC)
OFF: Power switch off
-
IG SW Power switch status ON or OFF ON: Power switch to ON
OFF: Power switch off
-
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
HINT:

If the certification ECU (smart key ECU assembly) misjudges that the power source is on even though the power source is off for any reason, the entry lock/unlock functions stop.


OK:

The main body ECU (multiplex network body ECU) judges properly that the power source is off when the power source is off.



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)

NG

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the I86 and I87 certification ECU (smart key ECU assembly) connectors.

B288569C10
2.042,0.219 2.396,0.448 0.354,0.229 5.292,0.208 5.646,0.438 0.354,0.229 1.417,0.958 1.177,1.396 false 6.063,1.01 6.26,1.479 false 5.885,1.01 5.688,1.49 false 2.125,0.271 2.406,0.448 0.281,0.177 10 false I86 0.198,0.094 0.479,0.271 0.281,0.177 10 false *a 1.104,1.406 1.458,1.583 0.354,0.177 10 false E 6.198,1.5 6.552,1.677 0.354,0.177 10 false +B 5.479,1.51 5.917,1.688 0.438,0.177 10 false CUTB 5.385,0.26 5.667,0.438 0.281,0.177 10 false I87
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I86-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I87-4 (CUTB) - Body ground Always 11 to 14 V
I87-5 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
a.

Disconnect the O2 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the O25 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
O2-15 (RCO) - O25-4 (+5) Always Below 1 Ω
O2-6 (RDAM) - O25-5 (DATA) Always Below 1 Ω
O2-7 (CSEL) - O25-2 (CSEL) Always Below 1 Ω
O2-15 (RCO) or O25-4 (+5) - Body ground Always 10 kΩ or higher
O2-6 (RDAM) or O25-5 (DATA) - Body ground Always 10 kΩ or higher
O2-7 (CSEL) or O25-2 (CSEL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

15.CHECK DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK DOOR CONTROL RECEIVER
a.
B274836C29
0.542,0.646 1.01,0.958 0.469,0.313 2.021,1.135 2.354,1.719 false 0.24,0.115 0.448,0.313 0.208,0.198 10 *a 2.208,1.74 2.625,1.938 0.417,0.198 10 GND 0.646,0.719 0.927,0.917 0.281,0.198 10 O25
*a Component with harness connected
(Door Control Receiver)


Connect the O25 door control receiver connector.


b.

Connect the O2 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O25-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

16.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274836C39
0.51,0.51 0.979,0.823 0.469,0.313 2.052,1.063 2.344,1.688 false 1.531,1.063 1.24,1.688 false 0.24,0.115 0.448,0.313 0.208,0.198 10 *a 0.604,0.573 0.896,0.771 0.292,0.198 10 O25 2.188,1.698 2.604,1.896 0.417,0.198 10 GND 1.135,1.698 1.344,1.885 0.208,0.188 10 +5
*a Component with harness connected
(Door Control Receiver)


Connect the O2 certification ECU (smart key ECU assembly) connector.


b.

Connect the O25 door control receiver connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O25-4 (+5) - O25-1 (GND) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch not pressed


Below 1 V
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch pressed


4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

17.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

17.CHECK DOOR CONTROL RECEIVER
a.

Connect the O2 certification ECU (smart key ECU assembly) connector.


b.

Connect the O25 door control receiver connector.


c.
B274836C30
0.51,0.552 0.979,0.865 0.469,0.313 2.063,1.094 2.74,1.583 false 1.375,1.104 0.948,1.594 false 1.906,1.115 2.167,1.604 false 0.271,0.198 0.479,0.396 0.208,0.198 10 *a 0.583,0.625 0.865,0.771 0.281,0.146 10 O25 2.625,1.615 3.021,1.771 0.396,0.156 10 GND 0.729,1.625 1.146,1.781 0.417,0.156 10 DATA 1.979,1.635 2.375,1.792 0.396,0.156 10 CSEL
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O25-5 (DATA) - O25-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed


Below 1 V → 11 to 14 V → Below 1 V
O25-2 (CSEL) - O25-1 (GND) Procedure:
1.

Power switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

19.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
19.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

OK:

Wireless door lock functions operate normally.


Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL


Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

20.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

21.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

22.CHECK KEY DIAGNOSTIC MODE
21.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

22.CHECK KEY DIAGNOSTIC MODE
22.CHECK KEY DIAGNOSTIC MODE
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK


OK:

Wireless door lock buzzer sounds.


Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
a.

Disconnect the O2 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the O25 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-7 (CSEL) - O25-2 (CSEL) Always Below 1 Ω
O2-7 (CSEL) or O25-2 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274836C31
0.563,0.646 1.031,0.958 0.469,0.313 2.052,1.094 2.74,1.688 false 1.896,1.125 2.146,1.698 false 0.24,0.115 0.448,0.313 0.208,0.198 10 *a 2.552,1.698 2.969,1.896 0.417,0.198 10 GND 0.667,0.719 0.948,0.917 0.281,0.198 10 O25 1.938,1.708 2.354,1.906 0.417,0.198 10 CSEL
*a Component with harness connected
(Door Control Receiver)


Connect the O2 certification ECU (smart key ECU assembly) connector.


b.

Connect the O25 door control receiver connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O25-2 (CSEL) - O25-1 (GND) Power switch off and all doors closed Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

25.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

25.CHECK DOOR CONTROL RECEIVER
a.

Connect the O2 certification ECU (smart key ECU assembly) connector.


b.

Connect the O25 door control receiver connector.


c.
B274836C40
0.563,0.854 1.031,1.167 0.469,0.313 2.052,1.104 2.479,1.594 false 1.365,1.104 0.938,1.594 false 0.271,0.198 0.479,0.396 0.208,0.198 10 *a 0.667,0.927 0.948,1.073 0.281,0.146 10 O25 2.333,1.604 2.729,1.76 0.396,0.156 10 GND 0.74,1.604 1.156,1.76 0.417,0.156 10 DATA
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


Standard Voltage:
Tester Connection Condition Specified Condition
O25-5 (DATA) - O25-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed*


Below 1 V → 11 to 14 V → Below 1 V


*: While the electrical key antennas are being inspected in key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

26.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

26.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

27.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
27.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)