Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG1 circuit, IG2 circuit or IG hold circuit in the power management control ECU is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*):
·

The IG1 or IG2 circuit in the power management control ECU is malfunctioning.

·

The IG hold circuit in the power management control ECU is malfunctioning.


·

AM2 fuse

·

Power management control ECU

·

Wire harness or connector


DTC Output Confirmation Operation

Turn the power switch on (IG).


HINT:

To turn the power switch on (IG), carry the electrical key transmitter sub-assembly and press the power switch twice with the shift lever in P and the brake pedal released.



*: Only detected while a malfunction is present and the power switch is on (IG)


HINT:
·

The IG1 and IG2 circuits activate the IG1 and IG2 relays.

·

After the IG1 and IG2 circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).



Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power switch cannot be turned on (IG) (the hybrid control system cannot be started). The power source mode cannot be changed to on (IG).

WIRING DIAGRAM

B296599E02
4.865,6.938 5.115,7.094 0.25,0.156 10 false IG2 4.406,7.313 6.188,7.51 1.781,0.198 10 false No. 1 Integration Relay 2.625,1.063 3.125,1.333 0.5,0.271 10 false IG1D 2.625,6.635 2.969,6.781 0.344,0.146 10 false IG2D 4.656,4.927 5.354,5.073 0.698,0.146 10 false IG1 NO. 4 3.625,5.385 6.406,5.688 2.781,0.302 10 false Instrument Panel Junction Block Assembly 1.958,7.188 3.229,7.552 1.271,0.365 10 false Power Management Control ECU 4.656,3.74 5.354,3.885 0.698,0.146 10 false IG1 NO. 3 4.656,2.563 5.354,2.708 0.698,0.146 10 false IG1 NO. 2 4.656,1.375 5.354,1.521 0.698,0.146 10 false IG1 NO. 1 3.104,6.438 3.219,6.583 0.115,0.146 10 false 2 3.125,0.885 3.385,1.156 0.26,0.271 10 false 2 3.104,1.063 3.438,1.25 0.333,0.188 10 false I4 3.021,6.615 3.354,6.802 0.333,0.188 10 false A39 4.021,6.615 4.323,6.771 0.302,0.156 10 false 1C 5.865,6.615 6.146,6.771 0.281,0.156 10 false 1E 4.073,6.448 4.26,6.604 0.188,0.156 10 false 8 5.896,6.427 6.083,6.583 0.188,0.156 10 false 2 3.594,0.646 3.927,0.896 0.333,0.25 10 false 3F 3.583,1.063 4.031,1.521 0.448,0.458 10 false 3A 3.594,0.896 4,1.323 0.406,0.427 10 false 27 3.625,0.479 3.833,0.635 0.208,0.156 10 false 1 6.198,0.656 6.448,0.844 0.25,0.188 10 false 3D 6.24,0.469 6.448,0.615 0.208,0.146 10 false 1 6.208,1.833 6.458,2.021 0.25,0.188 10 false 3D 6.208,1.656 6.604,1.927 0.396,0.271 10 false 36 6.198,3.01 6.448,3.198 0.25,0.188 10 false 3C 6.208,2.823 6.625,3.313 0.417,0.49 10 false 33 6.198,4.615 6.479,4.802 0.281,0.188 10 false 3B 6.25,4.438 6.458,4.583 0.208,0.146 10 false 7 5.625,0.802 6.156,1 0.531,0.198 10 false WIPER 5.646,2.021 6.219,2.5 0.573,0.479 10 false ECU-IG1 NO. 1 5.646,3.198 6.24,3.698 0.594,0.5 10 false ECU-IG1 NO. 3 0.01,1.583 0.865,2.177 0.854,0.594 10 false from Auxiliary Battery 1.156,1.729 1.771,2.135 0.615,0.406 10 false AM2 2.219,1.594 2.875,1.948 0.656,0.354 10 false AM21 1.948,1.406 2.219,1.615 0.271,0.208 10 false 7 1.927,1.583 2.292,1.896 0.365,0.313 10 false I4 2.219,2 2.854,2.354 0.635,0.354 10 false AM22 1.938,1.792 2.177,2.104 0.24,0.313 10 false 1 1.927,1.979 2.198,2.167 0.271,0.188 10 false I3 2.219,3.99 2.75,4.385 0.531,0.396 10 false E01 1.938,3.792 2.052,3.938 0.115,0.146 10 false 5 1.927,3.979 2.198,4.167 0.271,0.188 10 false I3 2.219,4.375 2.656,4.521 0.438,0.146 10 false E02 1.938,4.188 2.052,4.333 0.115,0.146 10 false 5 1.938,4.375 2.208,4.563 0.271,0.188 10 false I4 2.219,4.844 2.813,5.115 0.594,0.271 10 false E1 1.938,4.656 2.052,4.802 0.115,0.146 10 false 6 1.927,4.844 2.198,5.031 0.271,0.188 10 false I3 2.219,5.24 2.656,5.385 0.438,0.146 10 false E12 1.938,5.063 2.052,5.208 0.115,0.146 10 false 4 1.927,5.24 2.198,5.427 0.271,0.188 10 false I4

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2271
Power Source Control
·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

Latch Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B223988C19
0.417,1.219 0.833,1.458 0.417,0.24 0.5,3.573 0.917,3.813 0.417,0.24 2.229,3.521 2.698,3.521 false 1.25,1.156 0.854,0.75 false 0.583,1.26 0.885,1.521 0.302,0.26 10 false I3 0.656,3.615 1.01,3.917 0.354,0.302 10 false I4 0.469,0.656 0.917,0.917 0.448,0.26 10 false AM22 2.74,3.448 3.271,3.802 0.531,0.354 10 false AM21 0.125,0.104 0.323,0.417 0.198,0.313 10 false *a
*a Front view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 and I4 connectors from the power management control ECU.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I3-1 (AM22) - Body ground Power switch off 11 to 14 V
I4-7 (AM21) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B223988C20
0.438,1.198 0.854,1.438 0.417,0.24 0.438,3.5 0.854,3.74 0.417,0.24 2.271,1.188 2.74,1.188 false 1.76,3.479 2.76,2.833 false 2.125,1.156 2.771,0.625 false 1.917,3.51 2.76,3.417 false 0.594,1.219 0.885,1.438 0.292,0.219 10 false I3 0.594,3.521 0.875,3.75 0.281,0.229 10 false I4 2.802,0.542 3.115,0.792 0.313,0.25 10 false E01 2.781,1.115 3.167,1.469 0.385,0.354 10 false E1 2.781,3.344 3.125,3.635 0.344,0.292 10 false E02 2.792,2.75 3.156,3.042 0.365,0.292 10 false E12 0.146,0.104 0.344,0.354 0.198,0.25 10 false *a
*a Front view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-5 (E01) - Body ground Always Below 1 Ω
I3-6 (E1) - Body ground Always Below 1 Ω
I4-4 (E12) - Body ground Always Below 1 Ω
I4-5 (E02) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER MANAGEMENT CONTROL ECU
a.

Reconnect the I3 and I4 power management control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
I4-2 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG