Use these procedures to troubleshoot the smart entry and start system (for Start Function).
*: Use the intelligent tester.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time |
| Where | Whether the problem occurs at a specific location |
| Under what conditions? | Whether the doors were locked or unlocked, whether the power switch was on, whether the hybrid control system has started |
| How did it happen? | Problem symptoms* |
*: Be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem, and then check for DTCs.
If the entry lock/unlock function does not operate for all doors.
If the entry lock function does not operate.
If the entry unlock function does not operate.
If both the entry lock and unlock functions do not operate.
If the wireless lock and unlock functions do not operate.
If there is no power even when the power switch is pressed (does not turn on (ACC)).
If the hybrid control system does not start with the push-button start function.
If the wireless answer-back buzzer and outside warning buzzers do not sound.
If the customer attempted to start the hybrid control system by touching the electrical key transmitter sub-assembly to the power switch and pressing the power switch.
If the interior warning buzzers do not sound.
If the steering does not unlock.
Any other details concerning the problem.
If it is thought that wave interference is likely, be sure to ask the customer in detail about the following points concerning the vehicle operating conditions, environment and problem.
Specific locations where the system does not operate (such as near TV towers, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc.).
Specific times when the system does not operate:Whether or not symptoms occurred immediately after purchase or only recently.Whether or not the symptoms occurred even when the electrical key transmitter sub-assembly was near the vehicle (electrical key antenna).
If the system does not operate only when near specific vehicles (there may be an effect from electric waves from the wireless systems of other vehicles).
If the system operates intermittently.
If the electrical key transmitter sub-assembly is bundled together with other items.
If the electrical key transmitter sub-assembly is carried together with other electronic devices, such as cell phones, personal computers, portable music players, other electrical keys, etc. (keep the electrical key transmitter sub-assembly at least 0.1 m (0.33 ft.) away from such items).
Where the electrical key transmitter sub-assembly is being kept when not in use:Whether or not the electrical key transmitter sub-assembly being placed within 1 m (3.28 ft.) of items such as TVs, DVD recorders, induction cookers, rice cookers, dishwashers, modems, cell phones, personal computers, microwave ovens, desk or floor lamps, cordless telephones, etc.
If there are electronic devices that transmit electric waves placed in the vehicle.
When the transmitter battery was last replaced (when the battery is low):The transmitter battery can be checked using the "Key Low Battery" item in the Data List.
If the customer installed any optional components (theft deterrent devices, wireless fog lights, etc.) to the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect auxiliary battery voltage.
11 to 14 V (power switch off)
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
Check for blown fuses, open or shorted wire harnesses, improperly connected connectors and other problems in areas that can be visually inspected.
| Proceed to |
|---|
| NEXT |
NEXT
Use the intelligent tester to check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs and note any codes that are output.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| Engine immobiliser system DTC is output | B |
| Smart entry and start system (for Entry Function) DTC is output | C |
| Smart entry and start system (for Start Function) DTC is output | D |
A
B
C
D
Refer to Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in problem symptoms table | A |
| Fault is listed in problem symptoms table | B |
A
B
Data List / Active Test
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs
Recheck for DTCs
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B