Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075055 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B292916
4.708,0.875 4.969,1.063 0.26,0.188 10 false 15 5.802,0.958 6.063,1.24 0.26,0.281 10 false 28 4.688,1.385 4.99,1.625 0.302,0.24 10 false 42 1.229,1.25 1.76,1.563 0.531,0.313 10 false HORN 2.479,2.01 3.094,2.313 0.615,0.302 10 false HORN 3.094,0.99 3.354,1.344 0.26,0.354 10 false 2 3.094,1.615 3.417,1.969 0.323,0.354 10 false 5 2.177,0.99 2.344,1.313 0.167,0.323 10 false 1 2.177,1.615 2.406,1.917 0.229,0.302 10 false 3 6.094,1.073 6.792,1.49 0.698,0.417 10 false HORN 5.365,3.438 7.021,3.802 1.656,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 4.688,4.448 7.156,5.292 2.469,0.844 10 false from Steering Pad Switch Assembly 4.74,2.063 5.813,2.615 1.073,0.552 10 false Instrument Panel Junction Block Assembly 1.365,2.49 3.25,2.875 1.885,0.385 10 false Engine Room Relay Block and Junction Block Assembly 2.583,4.563 2.885,4.781 0.302,0.219 10 false A1 2.281,4.5 2.542,5 0.26,0.5 10 false 1 2.583,4.74 4.031,5.01 1.448,0.271 10 false High Pitched Horn 0.948,0.302 2.604,0.656 1.656,0.354 10 false from Auxiliary Battery 4.677,1.594 5.042,1.875 0.365,0.281 10 false 3A 4.667,1.094 4.969,1.417 0.302,0.323 10 false 3D 5.365,3.281 5.729,3.552 0.365,0.271 10 false MB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT HORNS
a.

Press the horn switch and check if the horns sound.

Result:
Result Proceed to
Horns sound A
Horns do not sound B




A

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B220554
1.073,0.51 1.448,0.74 0.375,0.229 4.719,0.5 5.094,0.729 0.375,0.229 6.292,1.26 6.292,1.51 6.292,1.51 6.115,1.51 false 0.146,0.135 0.677,0.51 0.531,0.375 10 *a 1.177,0.542 1.865,0.844 0.688,0.302 10 3D 4.813,0.542 5.354,0.875 0.542,0.333 10 MB 5.656,1.448 6.438,1.708 0.781,0.26 10 HORN
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-15 - MB-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY