Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075062 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the power switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a past DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Terminal AGND, VC5, TXCT or CODE is open (includes disconnection of the power switch).

·

The transponder key amplifier coil built into the power switch is open.


·

Power switch

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

With the shift lever in P, the key held near the power switch and a hybrid control system start operation is performed by pressing and holding the power switch when the key battery is depleted.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when key battery is depleted by holding key near power switch and pressing and holding power switch with shift lever in P -

Related Data List and Active Test
DTC Code Data List and Active Test
B2784 -

WIRING DIAGRAM

B278927
5.069,2.816 6.642,3.16 1.573,0.344 10 Certification ECU (Smart Key ECU Assembly) 0.908,2.984 1.814,3.134 0.906,0.149 10 Power Switch 0.908,2.83 1.148,2.98 0.24,0.149 10 I58 5.006,0.722 5.246,0.871 0.24,0.149 10 I87 5.048,0.54 5.152,0.689 0.104,0.149 10 9 1.952,0.614 2.135,0.764 0.183,0.149 10 10 1.952,1.133 2.065,1.282 0.113,0.149 10 7 1.952,1.665 2.065,1.814 0.113,0.149 10 8 1.952,2.179 2.065,2.328 0.113,0.149 10 6 5.048,1.072 5.152,1.221 0.104,0.149 10 3 5.048,2.102 5.152,2.251 0.104,0.149 10 6 5.006,1.587 5.194,1.736 0.188,0.149 10 13 5.311,0.722 5.61,0.871 0.299,0.149 10 VC5 1.598,0.722 1.897,0.871 0.299,0.149 10 VC5 5.311,1.237 5.703,1.386 0.392,0.149 10 TXCT 1.486,1.237 1.879,1.386 0.392,0.149 10 TXCT 5.311,1.755 5.742,1.904 0.431,0.149 10 CODE 1.448,1.755 1.878,1.904 0.431,0.149 10 CODE 5.311,2.273 5.742,2.423 0.431,0.149 10 AGND 1.448,2.273 1.878,2.423 0.431,0.149 10 AGND 5.006,1.244 5.246,1.393 0.24,0.149 10 I87 5.006,1.762 5.246,1.911 0.24,0.149 10 I87 5.006,2.273 5.246,2.423 0.24,0.149 10 I86

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the I86 and I87 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I58 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I87-13 (CODE) - I58-8 (CODE) Always Below 1 Ω
I87-3 (TXCT) - I58-7 (TXCT) Always Below 1 Ω
I87-9 (VC5) - I58-10 (VC5) Always Below 1 Ω
I86-6 (AGND) - I58-6 (AGND) Always Below 1 Ω
I58-8 (CODE) - Body ground Always 10 kΩ or higher
I58-7 (TXCT) - Body ground Always 10 kΩ or higher
I58-10 (VC5) - Body ground Always 10 kΩ or higher
I58-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE POWER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE POWER SWITCH
a.

Temporarily replace the power switch with a new or known good one.

Click hereEngine / Hybrid System>2AR-FXE STARTING>POWER SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER SWITCH WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)