Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2012.02–2015.04
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075079 STEERING PAD N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a horn button assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the horn button assembly.

·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 45130 2.DISPOSE OF HORN BUTTON ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the horn button assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a 12 V battery as the power source to deploy the airbag.


a.
C110371N45
0.948,1.208 0.729,0.781 0.729,0.781 0.563,0.781 false 0.271,0.698 0.646,0.99 0.375,0.292 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS Airbag Deployment Tool


i.
C110372C06
0.5,0.698 0.833,0.698 0.833,0.698 0.833,1.625 false 2.708,0.74 2.51,0.74 false 0.208,0.615 0.646,0.906 0.438,0.292 10 false SST 2.729,0.635 2.948,0.833 0.219,0.198 10 false *1
*1 12 V Battery


Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N08
1.75,0.635 1.458,0.333 false 1.177,0.198 1.531,0.448 0.354,0.25 10 false SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.




c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



d.

Remove the lower steering column cover (Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).


e.

Disconnect the yellow airbag connector from the spiral cable.

i.
B279733C02
0.927,2.333 1.219,2.042 1.219,2.042 1.448,2.042 true 1.479,1.958 1.708,2.156 0.229,0.198 10 false *a
*a Slider


Slide the slider to release the lock, and then disconnect the connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




f.

Install SST.

CAUTION:

Check that there is no looseness in the steering wheel assembly and horn button assembly.


i.
B312067N01
1.375,1.604 1.375,1.813 1.375,1.813 1.938,1.813 false 1.615,1.604 1.615,1.813 false 1.969,1.74 2.406,2.063 0.438,0.323 10 false SST

Connect the SST connector to the airbag connector of the spiral cable.

SST
09082-00700  
09082-00780  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
B300292C01
1.094,0.177 1.542,0.177 1.542,0.177 1.635,0.417 false 2.719,1.594 2.927,1.594 false 2.958,1.521 3.344,1.76 0.385,0.24 10 false SST 1.552,1.823 1.792,2.052 0.24,0.229 10 false *a 0.938,0.104 1.167,0.344 0.229,0.24 10 false *1
*1 12 V Battery
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


iii.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



g.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch to deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 45130 3.DISPOSE OF HORN BUTTON ASSEMBLY (When Not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a 12 V battery as the power source to deploy the airbag.


a.
C110371N45
0.948,1.208 0.729,0.781 0.729,0.781 0.563,0.781 false 0.271,0.698 0.646,0.99 0.375,0.292 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS Airbag Deployment Tool


i.
C110372C06
0.5,0.698 0.833,0.698 0.833,0.698 0.833,1.625 false 2.708,0.74 2.51,0.74 false 0.208,0.615 0.646,0.906 0.438,0.292 10 false SST 2.729,0.635 2.948,0.833 0.219,0.198 10 false *1
*1 12 V Battery


Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N08
1.75,0.635 1.458,0.333 false 1.177,0.198 1.531,0.448 0.354,0.25 10 false SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.



b.

Remove the horn button assembly (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL).

CAUTION:
·

Before removing the horn button assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When storing the horn button assembly, keep the airbag deployment side facing upward.




c.
B104882C14
2.302,0.938 2.042,0.427 2.042,0.427 1.865,0.427 false 2.656,1.469 2.896,1.729 0.24,0.26 10 false *a 1.719,0.344 1.927,0.531 0.208,0.188 10 false *1
*1 Stripped Wire Section
*a Wire Diameter


Using braided wire, tie down the horn button assembly to an unneeded wheel.

Wire:

Stripped wire section

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the horn button assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4


i.
B289018N01
2.26,1.938 2.26,1.281 2.26,1.281 2.917,1.281 false 2.604,1.833 2.604,1.281 false 2.948,1.198 3.302,1.49 0.354,0.292 10 false SST

After connecting the following SST to each other, connect them to the horn button assembly.

SST
09082-00802  (09082-10801, 09082-40800)


ii.
B289019C02
2.302,0.938 2.135,1.073 2.135,1.073 1.979,1.073 false 1.344,0.896 1.344,1.156 false 1.083,1.948 1.083,1.51 1.083,1.51 2.688,1.51 false 2.323,1.948 2.323,1.521 false 1.813,2.885 2.427,2.885 false 1.26,1.125 1.417,1.323 0.156,0.198 10 false *a 1.833,0.979 1.99,1.177 0.156,0.198 10 false *a 2.458,2.792 2.75,3.052 0.292,0.26 10 false *a 2.708,1.396 2.927,1.646 0.219,0.25 10 false *a
*a 2 times or more


Wind 3 wires at least 2 times each around each of the snap pins.

CAUTION:
·

Tightly wind the wires around the snap pins without any slack.

·

Make sure that the wires are tight. If there is slack in the wires, the horn button assembly may break loose when the airbag is deployed.




iii.
B289020

Face the airbag deployment side of the horn button assembly upward on top of an unneeded tire and wheel set. Separately tie each side of the horn button assembly to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the horn button assembly may break loose when the airbag is deployed.

·

Always tie down the horn button assembly with the airbag deployment side facing upward.



NOTICE:

The wheel will be damaged by the airbag deployment, so use an unneeded wheel.




d.
B289021N01
2.969,1.104 3.177,1.104 false 2.688,1.031 3.094,1.26 0.406,0.229 10 false SST

Install SST.

CAUTION:

Place the wheel on level ground.


i.

Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the disc wheel.



ii.
C265776C01
0.938,1.51 1.302,1.51 false 1.344,1.427 1.719,1.667 0.375,0.24 10 false SST 1.344,1.802 1.563,2.021 0.219,0.219 10 false *a
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the wheel.



e.

Cover the horn button assembly (using a cardboard box).

i.
C188669C03
2.396,1.583 2.875,1.583 true 1,1.49 0.604,1.49 true 1.198,0.146 1.375,0.354 0.177,0.208 10 false Y 1.052,0.729 1.219,0.927 0.167,0.198 10 false Y 2.781,0.885 2.969,1.094 0.188,0.208 10 false X 0.448,1.417 0.719,1.646 0.271,0.229 10 false *1 2.906,1.5 3.177,1.76 0.271,0.26 10 false *1
*1 Weight


Cover the horn button assembly with a cardboard box.


ii.

Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

Minimum cardboard box size:

Must exceed the following dimensions

X:

460 mm (1.51 ft.)

Y:

650 mm (2.13 ft.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the diameter of the wheel and tire to which the horn button assembly is tied, X should be the following size.

X = 460 mm (1.51 ft.) + width of tire

·

If a cardboard box smaller than the specified size is used, it may be broken by the shock from the airbag deployment.





f.

Cover the horn button assembly (using tires).

i.
B289022C01
0.563,1.823 0.75,2.052 0.188,0.229 10 false *1 1.646,0.302 1.885,0.51 0.24,0.208 10 false *a 2.688,0.875 2.885,1.094 0.198,0.219 10 false *b
*1 Tires (3 or more)
*a Inner Diameter
*b Width


Place at least 3 tires without wheels onto the wheel and tire to which the horn button assembly is tied.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)



ii.

Place a wheel and tire on top.

CAUTION:

Do not use tires with wheels except for on the top and bottom.


NOTICE:
·

The tires may be damaged by the airbag deployment, so use unneeded tires.

·

Do not place the SST connector under the tire because it could be damaged.




iii.
C223306

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




g.

Deploy the airbag.

i.
C188670C03
2.542,1.469 2.917,1.844 2.917,1.844 2.917,2.031 true 2.656,3.5 2.979,3.823 2.979,3.823 2.979,4.021 true 1.385,3.375 1.688,3.375 false 0.729,1.219 0.5,1.219 false 0.396,3.24 0.74,3.24 false 1.385,1.375 1.656,1.375 false 1.385,2.042 1.625,2.302 0.24,0.26 10 false *a 0.208,2.323 0.521,2.604 0.313,0.281 10 false *B 0.208,0.073 0.552,0.375 0.344,0.302 10 false *A 2.833,2.042 3.073,2.24 0.24,0.198 10 false *2 1.677,1.271 1.896,1.51 0.219,0.24 10 false *1 0.229,1.135 0.594,1.406 0.365,0.271 10 false SST 0.115,3.156 0.479,3.438 0.365,0.281 10 false SST 1.708,3.281 1.875,3.458 0.167,0.177 10 false *1 2.896,4.031 3.115,4.24 0.219,0.208 10 false *2 1.375,4.083 1.604,4.313 0.229,0.229 10 false *a
*A Using a Cardboard Box
*B Using Tires
*1 12 V Battery
*2 Horn Button Assembly
*a 10 m (32.8 ft.) or more


Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the horn button assembly is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the horn button assembly.

CAUTION:
·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the horn button assembly from the wheel.


ii.

Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.