84306
1.INSPECT SPIRAL CABLE SUB-ASSEMBLY
Do not remove the steering sensor from the spiral cable sub-assembly.
As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.
Remove the spiral cable with sensor sub-assembly from the vehicle (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).
Visually check for defects with the spiral cable sub-assembly.
The defects are as follows:
Scratches
Small cracks
Dents
Chips
Cracks or other damage to the connector
No defects are found.
If any of the defects is found, replace the spiral cable sub-assembly with a new one.
Check the spiral cable sub-assembly.
| *a | Component without harness connected
(Spiral Cable Sub-assembly) |
- | - |
|
Interlock | - | - |
When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.
Set the spiral cable sub-assembly to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).
Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I28-1 (CCS) - z2-3 | Always | 3 Ω or less |
| I28-2 (ECC) - z2-4 | Always | 3 Ω or less |
| I28-3 (EAU) - z3-8 | Always | 3 Ω or less |
| I28-4 (AU3) - z3-9 | Always | 3 Ω or less |
| I28-5 (AU2) - z3-10 | Always | 3 Ω or less |
| I28-6 (AU1) - z3-11 | Always | 3 Ω or less |
| I28-9 (HO) - z3-1 | Always | 3 Ω or less |
| I28-10 (+DP) - z3-2 | Always | 3 Ω or less |
| I28-11 (-DP) - z3-3 | Always | 3 Ω or less |
| I28-13 (IL+2) - z3-5 | Always | 3 Ω or less |
| I27-1 (D+) - z4-2 | Always | Below 1 Ω |
| I27-2 (D-) - z4-1 | Always | Below 1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I28-1 (CCS) - z2-3 | Always | 3 Ω or less |
| I28-2 (ECC) - z2-4 | Always | 3 Ω or less |
| I28-3 (EAU) - z3-8 | Always | 3 Ω or less |
| I28-4 (AU3) - z3-9 | Always | 3 Ω or less |
| I28-5 (AU2) - z3-10 | Always | 3 Ω or less |
| I28-6 (AU1) - z3-11 | Always | 3 Ω or less |
| I28-9 (HO) - z3-1 | Always | 3 Ω or less |
| I28-10 (+DP) - z3-2 | Always | 3 Ω or less |
| I28-11 (-DP) - z3-3 | Always | 3 Ω or less |
| I28-13 (IL+2) - z3-5 | Always | 3 Ω or less |
| I27-1 (D+) - z4-2 | Always | Below 1 Ω |
| I27-2 (D-) - z4-1 | Always | Below 1 Ω |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I28-1 (CCS) - z2-3 | Always | 3 Ω or less |
| I28-2 (ECC) - z2-4 | Always | 3 Ω or less |
| I28-3 (EAU) - z3-8 | Always | 3 Ω or less |
| I28-4 (AU3) - z3-9 | Always | 3 Ω or less |
| I28-5 (AU2) - z3-10 | Always | 3 Ω or less |
| I28-6 (AU1) - z3-11 | Always | 3 Ω or less |
| I28-9 (HO) - z3-1 | Always | 3 Ω or less |
| I28-10 (+DP) - z3-2 | Always | 3 Ω or less |
| I28-11 (-DP) - z3-3 | Always | 3 Ω or less |
| I28-13 (IL+2) - z3-5 | Always | 3 Ω or less |
| I27-1 (D+) - z4-2 | Always | Below 1 Ω |
| I27-2 (D-) - z4-1 | Always | Below 1 Ω |
If the result is not as specified, replace the spiral cable with sensor sub-assembly.