Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075080 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


PROCEDURE

Hide 45100 1.REMOVE STEERING WHEEL ASSEMBLY

Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.
B474842C02
0.677,0.542 0.677,0.719 0.677,0.719 0.333,0.719 true 0.708,1.531 0.302,1.531 true 0.073,0.125 0.385,0.281 0.313,0.156 10 false *A 0.083,1.125 0.396,1.281 0.313,0.156 10 false *B 0.177,0.615 0.385,0.792 0.208,0.177 10 false *a 0.135,1.448 0.448,1.604 0.313,0.156 10 false *b
*A Flat Cable Type
*B Colored Roller Type
*a Flat Cable
*b Colored Roller


Check the colored roller or flat cable shown in the illustration.

If the colored roller or flat cable shown in the illustration cannot be confirmed, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable with sensor sub-assembly with a new one.


Hide 45287 4.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 5.REMOVE UPPER STEERING COLUMN COVER

Hide 84307 6.REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.


c.

Check that the front wheels are facing straight ahead.


d.
B279735C04
0.896,2.302 1.229,2.01 1.229,2.01 1.458,2.01 false 1.49,1.927 1.708,2.156 0.219,0.229 10 false *a
*a Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



e.

Disconnect the other connector from the spiral cable with sensor sub-assembly.


f.
B279736

Disengage the 3 claws to remove the spiral cable with sensor sub-assembly.


Hide 84306 7.REMOVE SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Remove the spiral cable sub-assembly from the steering sensor only when replacing it or the steering sensor.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in a misaligned center position of the steering sensor. Therefore, make sure to use the lock pin provided with a new spiral cable sub-assembly or steering sensor when removing the steering sensor from the spiral cable sub-assembly.

·


a.
C238437

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable sub-assembly.

·

Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.




b.
B279788C02
0.938,0.74 1.844,0.365 false 0.979,1.281 1.823,1.813 false 1.854,0.26 2.083,0.469 0.229,0.208 10 false *1 1.854,1.75 2.063,1.948 0.208,0.198 10 false *1
*1 Guide


Disengage the 6 claws and 2 pins to remove the spiral cable sub-assembly from the steering sensor.

NOTICE:
·

Do not damage the claw of the steering sensor.

·

Do not damage the guide.