Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075082 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 62170A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Temporarily install the curtain shield airbag assembly with the 2 hooks.

B282225N02
4.073,2.417 4.281,2.646 0.208,0.229 10 false 1 4.531,2.417 4.76,2.646 0.229,0.229 10 false 2

NOTICE:
·

When installing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.

·

Do not twist the curtain shield airbag assembly when installing it.




d.

Install 2 new bolts in the order shown in the illustration.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)


e.

Install the curtain shield airbag assembly to the body panel with 5 claws, 6 new clips and 2 new spacers in the order shown in the illustration.

B282226C02
1.26,1.885 1.406,1.646 1.406,1.646 1.479,1.646 false 1.021,1.99 0.833,1.99 0.833,1.99 0.604,2.177 false 0.958,2.177 0.75,2.5 0.75,2.5 0.594,2.5 false 1.083,2.208 1.083,2.302 false 1.427,2.24 1.427,2.323 false 3.531,0.604 3.729,0.813 0.198,0.208 10 false 1 3.094,1.615 3.281,1.813 0.188,0.198 10 false 2 2.052,0.667 2.26,0.885 0.208,0.219 10 false 3 1.99,1.917 2.146,2.094 0.156,0.177 10 true 4 1.073,0.948 1.25,1.156 0.177,0.208 10 false 5 0.438,1.24 0.594,1.427 0.156,0.188 10 false 6 4.479,1.604 4.667,1.802 0.188,0.198 10 false 7 5.24,2 5.417,2.188 0.177,0.188 10 true 8 5.979,2.146 6.177,2.323 0.198,0.177 10 true 10 5.729,0.844 5.906,1.031 0.177,0.188 10 false 9 6.635,1.115 6.854,1.344 0.219,0.229 10 true 11 1.51,1.563 1.688,1.719 0.177,0.156 10 false *1 0.458,2.094 0.635,2.25 0.177,0.156 10 false *2 1.344,2.323 1.521,2.479 0.177,0.156 10 false *4 0.458,2.417 0.635,2.573 0.177,0.156 10 false *3 1,2.302 1.177,2.458 0.177,0.156 10 false *5
*1 Pin *2 Clip
*3 Curtain Shield Airbag Assembly *4 Body Panel
*5 Spacer - -



f.
B282227

Push in a new pin to each clip.

NOTICE:

Make sure that the pins of the clips are pushed in firmly.



g.
B282228C02
2.521,0.635 2.646,0.635 false 1.531,1.875 1.26,1.604 1.26,1.604 0.844,1.604 false 2.688,0.563 2.906,0.74 0.219,0.177 10 false *2 0.677,1.531 0.844,1.698 0.167,0.167 10 false *1
*1 Airbag Connector
*2 Airbag Connector Lock


Connect the curtain shield airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



h.

Push in the lock to install the curtain shield airbag connector.


Hide 2.INSTALL ROOF HEADLINING ASSEMBLY