1.INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
| *1 | Clip (Black) |
| *2 | Clip (White) |
Install the 2 clips to the roof headlining assembly.
Put the roof headlining assembly into the vehicle through the front door RH.
Do not damage the roof headlining assembly or body interior.
Engage the 2 clips.
| *A | w/ Digital Audio Broadcasting Antenna | - | - |
Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
w/ Digital Audio Broadcasting Antenna:
Engage the clamp and connect the connector to the rear pillar LH.
w/ Rain Sensor:
Connect the connector to the rain sensor.
w/ EC Mirror:
Connect the connector to the inner rear view mirror.
2.INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
| *1 | Clip (Black) |
| *2 | Clip (White) |
Install the 2 clips to the roof headlining assembly.
Put the roof headlining assembly into the vehicle through the front door RH.
Do not damage the roof headlining assembly or body interior.
Engage the 2 clips and 2 fasteners.
| *A | w/ Digital Audio Broadcasting Antenna | - | - |
Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
Connect the connector to the sliding roof drive gear assembly.
w/ Digital Audio Broadcasting Antenna:
Engage the clamp and connect the connector to the rear pillar LH.
w/ Rain Sensor:
Connect the connector to the rain sensor.
w/ EC Mirror:
Connect the connector to the inner rear view mirror.
74348
3.INSTALL VISOR HOLDER
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
Use the same procedure for the other visor holder.
74310
4.INSTALL VISOR ASSEMBLY RH
Install the visor assembly RH with the 2 screws.
74325
5.INSTALL VISOR BRACKET COVER (for RH Side)
Engage the 4 claws to install the visor bracket cover.
74320
6.INSTALL VISOR ASSEMBLY LH
Use the same procedure as for the RH side.
74325
7.INSTALL VISOR BRACKET COVER (for LH Side)
Use the same procedure as for the RH side.
63318C
8.INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
| *1 | Notch |
| *2 | Alignment Mark |
Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
After installation, check that the corners fit correctly.
74610A
9.INSTALL ASSIST GRIP SUB-ASSEMBLY (for RH Side)
Put an assist grip sub-assembly together as shown in the illustration.
Engage the 2 clips to install the assist grip sub-assembly.
Engage the 4 claws to install the 2 assist grip covers
74610A
10.INSTALL ASSIST GRIP SUB-ASSEMBLY (for LH Side)
Use the same procedure as for the RH side.
74620C
11.INSTALL REAR ASSIST GRIP ASSEMBLY RH
Put an rear assist grip assembly RH together as shown in the illustration.
Engage the 2 clips to install the rear assist grip assembly RH.
Engage the 4 claws to install the 2 assist grip covers
74630E
12.INSTALL REAR ASSIST GRIP ASSEMBLY LH
Use the same procedure as for the RH side.
81240
13.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)
81360T
14.INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)
63650A
15.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)
63650A
16.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)
89943
17.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
87834
18.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
19.INSTALL INSTRUMENT PANEL SAFETY PAD
20.INSTALL FRONT SEAT ASSEMBLY RH
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION
21.INSTALL FRONT SEAT ASSEMBLY LH
Use the same procedure as for the RH side.
62471A
22.INSTALL ROOF SIDE INNER GARNISH RH
Engage the 2 guides.
Engage the 5 clips to install the roof side inner garnish RH.
62411B
23.INSTALL CENTER PILLAR UPPER GARNISH RH
Pass the floor anchor of the front seat outer seat belt assembly RH through the center pillar upper garnish RH.
Engage the clip.
Install the center pillar upper garnish RH with the 2 screws.
62413A
24.INSTALL CENTER PILLAR LOWER GARNISH RH
Engage the 2 claws and 3 clips to install the center pillar lower garnish RH.
73210
25.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
73233
26.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
62331A
27.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
| *1 | Alignment Mark (Blue) |
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
After installation, check that the corners fit correctly.
67917A
28.INSTALL REAR DOOR SCUFF PLATE RH
Engage the 6 claws to install the rear door scuff plate LH.
Engage the claws from the rear side of the scuff plate.
62472A
29.INSTALL ROOF SIDE INNER GARNISH LH
Use the same procedure as for the RH side.
62412B
30.INSTALL CENTER PILLAR UPPER GARNISH LH
Use the same procedure as for the RH side.
62414A
31.INSTALL CENTER PILLAR LOWER GARNISH LH
Use the same procedure as for the RH side.
73220
32.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Use the same procedure as for the RH side.
73233
33.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
Use the same procedure as for the RH side.
62332A
34.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
| *1 | Alignment Mark (Red) |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
After installation, check that the corners fit correctly.
67918A
35.INSTALL REAR DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
36.INSTALL REAR SIDE SEATBACK ASSEMBLY LH
37.INSTALL REAR SIDE SEATBACK ASSEMBLY RH
38.INSTALL REAR SEATBACK ASSEMBLY LH
64277C
39.INSTALL NO. 2 ROOM PARTITION COVER
40.INSTALL REAR SEATBACK ASSEMBLY RH
72693
41.INSTALL REAR SEAT CUSHION LOCK HOOK
42.INSTALL REAR SEAT CUSHION ASSEMBLY
62211
43.INSTALL FRONT PILLAR GARNISH RH
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
If there is any damage, replace the garnish clip with a new one.
Install the front pillar garnish clip to front pillar garnish RH.
Install the front pillar garnish clip so that it faces as shown in the illustration.
| *a | Correct | *b | Incorrect |
Engage the 2 guides as shown in the illustration.
Engage the 2 clips to install the front pillar garnish RH.
62311B
44.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
| *1 | Alignment Mark (White) |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
After installation, check that the corners fit correctly.
62111A
45.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.
Install the cowl side trim sub-assembly RH with the clip.
67913
46.INSTALL FRONT DOOR SCUFF PLATE RH
Engage the 10 claws to install the front door scuff plate RH.
62212
47.INSTALL FRONT PILLAR GARNISH LH
Use the same procedure as for the RH side.
62312B
48.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
| *1 | Alignment Mark (Yellow) |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
After installation, check that the corners fit correctly.
62112A
49.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Use the same procedure as for the RH side.
67914
50.INSTALL FRONT DOOR SCUFF PLATE LH
Use the same procedure as for the RH side.
51.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
64718C
52.INSTALL LUGGAGE TRIM SERVICE HOLE COVER
53.INSPECT SRS WARNING LIGHT