Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075083 FRONT SEAT SIDE AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a front seat airbag assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the front seat airbag assembly.

·

The front seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat airbag assembly with a deployed airbag.

·

Do not apply water etc. to a front seat airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the front seat airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 73920A 2.DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the front seat airbag assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a 12 V battery as the power source to deploy the airbag.


a.
C110371N45
0.948,1.208 0.729,0.781 0.729,0.781 0.563,0.781 false 0.271,0.698 0.646,0.99 0.375,0.292 10 false SST

Check the function of SST (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL).

SST
09082-00700  



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



d.

Disconnect the connector from the front seat airbag assembly under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.
B279750C05
1.781,1.052 2.302,1.052 false 2.313,0.948 2.615,1.25 0.302,0.302 10 false *a
*a Slider


Slide the slider to release the lock, and then disconnect the yellow airbag connector as shown in the illustration.



e.

Install SST.

CAUTION:

Check that there is no looseness in the front seat assembly.


i.
B300291N01
1.917,1.5 1.917,1.188 1.917,1.188 2.615,1.188 false 2.375,1.51 2.375,1.188 false 2.646,1.104 3.073,1.375 0.427,0.271 10 false SST

Connect the SST connector to the front seat airbag assembly connector.

SST
09082-00700  
09082-00820  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
B300292C01
1.094,0.177 1.542,0.177 1.542,0.177 1.635,0.417 false 2.719,1.594 2.927,1.594 false 2.958,1.521 3.344,1.76 0.385,0.24 10 false SST 1.552,1.823 1.792,2.052 0.24,0.229 10 false *a 0.938,0.104 1.167,0.344 0.229,0.24 10 false *1
*1 12 V Battery
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window.


iii.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



f.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch to deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The front seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat airbag assembly with a deployed airbag.

·

Do not apply water etc. to a front seat airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 73920A 3.DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY (When Not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a 12 V battery as the power source to deploy the airbag.


a.
C110371N45
0.948,1.208 0.729,0.781 0.729,0.781 0.563,0.781 false 0.271,0.698 0.646,0.99 0.375,0.292 10 false SST

Check the function of SST (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL).

SST
09082-00700  


b.

Remove the front seat airbag assembly (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT SEAT SIDE AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

Before removing the front seat assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the negative (-) auxiliary battery terminal.

·

When storing the front seat airbag assembly, keep the airbag deployment side facing upward.




c.
B104882C14
2.302,0.938 2.042,0.427 2.042,0.427 1.865,0.427 false 2.656,1.469 2.896,1.729 0.24,0.26 10 false *a 1.719,0.344 1.927,0.531 0.208,0.188 10 false *1
*1 Stripped Wire Section
*a Wire Diameter


Using braided wire, tie down the front seat airbag assembly to an unneeded tire.

Wire:

Stripped wire section

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the front seat airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4


i.
B286411

Install the 2 nuts to the front seat airbag assembly.


ii.
B300293

Wind the wires around the front seat airbag assembly as shown in the illustration.


iii.
B300294C01
1.948,0.188 2.219,0.469 0.271,0.281 10 false *a 2.625,1.448 2.938,1.74 0.313,0.292 10 false *b
*a Width
*b Inner Diameter


Position the front seat airbag assembly inside the tire.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the front seat airbag assembly may break loose when the airbag is deployed.

·

Face the front seat airbag assembly deployment surface toward the inside the tire to evenly distribute the force of deployment.



NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tire.




d.

Install SST.

i.
B300295N01
0.802,1.229 0.552,1.229 false 0.271,1.146 0.667,1.427 0.396,0.281 10 false SST

Connect the SST connector to the front seat airbag assembly connector.

SST
09082-00820  



e.

Place the tires.

i.
B300296C01
1.49,0.052 1.75,0.333 0.26,0.281 10 false *a 0.677,1.521 0.917,1.75 0.24,0.229 10 false *1 0.677,0.677 0.927,0.938 0.25,0.26 10 false *1 2.229,0.854 2.479,1.104 0.25,0.25 10 false *b
*1 Tires (2 or more)
*a Inner Diameter
*b Width


Place at least 2 tires under the tire to which the front seat airbag assembly is tied.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


NOTICE:
·

The tires may be damaged by the airbag deployment, so use unneeded tires.

·

Do not place the SST connector under the tire because it could be damaged.




ii.

Place at least 2 tires onto the tire to which the front seat airbag assembly is tied. The top tire should have a wheel installed.


iii.
C223306

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




f.

Install SST.

i.
B279757C02
1.625,0.427 2.135,0.427 2.135,0.427 2.417,1.208 false 1.427,1.99 1.635,1.99 false 0.354,2.792 0.354,2.948 false 0.208,2.969 0.635,3.292 0.427,0.323 10 false SST 1.188,2.969 1.448,3.281 0.26,0.313 10 false *a 1.667,1.896 1.979,2.198 0.313,0.302 10 false *2 1.469,0.344 1.76,0.625 0.292,0.281 10 false *1
*1 Front Seat Airbag Assembly
*2 12 V battery
*a 10 m (32.8 ft.) or more


Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.



g.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat airbag assembly is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the front seat airbag assembly.

CAUTION:
·

The front seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat airbag assembly with a deployed airbag.

·

Do not apply water etc. to a front seat airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the front seat airbag assembly from the tire.


ii.

Place the front seat airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.