Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075086 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67913 4.REMOVE FRONT DOOR SCUFF PLATE

Hide 62311B 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 67917A 6.REMOVE REAR DOOR SCUFF PLATE

Hide 62331A 7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.


Hide 62413A 8.REMOVE CENTER PILLAR LOWER GARNISH

Hide 89860 9.REMOVE SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the side airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

B286417C02
1.448,1.719 1.5,1.719 1.5,1.719 1.656,1.875 false 1.885,2.094 1.969,2.177 1.969,2.177 1.969,2.344 false 3.833,2.083 3.917,2.167 3.917,2.167 3.917,2.333 false 3.396,1.719 3.448,1.719 3.448,1.719 3.604,1.875 false 1.292,1.823 1.354,1.823 1.354,1.823 1.531,2 false 3.24,1.823 3.302,1.823 3.302,1.823 3.479,2 false 1.302,1.635 1.5,1.833 0.198,0.198 10 false *1 1.885,2.354 2.094,2.563 0.208,0.208 10 false *2 1.542,2.406 1.76,2.615 0.219,0.208 10 false *a 1.698,1.573 1.917,1.781 0.219,0.208 10 false *b 3.24,1.635 3.438,1.833 0.198,0.198 10 false *1 3.833,2.344 4.052,2.563 0.219,0.219 10 false *2 3.469,2.417 3.667,2.635 0.198,0.219 10 false *a 3.604,1.573 3.813,1.76 0.208,0.188 10 false *b 1.083,1.729 1.302,1.958 0.219,0.229 10 false (A) 3.031,1.729 3.302,1.958 0.271,0.229 10 false (A)
*1 White Housing Lock *2 Yellow CPA
*a Slide *b Push



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




d.

Remove the bolt and side airbag sensor assembly from the vehicle body.

NOTICE:

Loosen the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.



e.

After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296256C05
5.01,0.51 5.292,0.792 0.281,0.281 10 false *b 1.792,0.51 2.063,0.792 0.271,0.281 10 false *a
*a Correct *b Incorrect