72211
1.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 springs to install the seat track adjusting handle to the separate type front seat cushion spring assembly.
71054S
2.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY
Install the 2 front seatback hooks to the front seatback spring sub-assembly.
Engage the 2 guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly.
Engage the 4 claws.
71587B
3.INSTALL FRONT SEATBACK EDGE PROTECTOR
Engage each claw to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.
71640S
4.INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
Engage the 4 guides to install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly.
Install the 4 bolts.
71538B
5.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Engage the 3 claws to install the front seat cushion edge protector LH.
Install the screw.
71537H
6.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Engage the 3 claws to install the front seat cushion edge protector RH.
Install the screw.
71876G
7.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Engage the guide to install the reclining adjuster inside cover LH.
71875F
8.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Engage the guide to install the reclining adjuster inside cover RH.
71074S
9.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
73920A
10.INSTALL FRONT SEAT AIRBAG ASSEMBLY
11.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Temporarily install the separate type front seatback cover with pad.
Install the 3 brackets with the 2 nuts.
For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the bracket securely.
Engage the 4 claws to install the 2 front seat headrest supports.
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Close the 2 fasteners.
Using hog ring pliers, install 5 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
71072S
12.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Temporarily install the separate type front seat cushion cover with pad.
Engage each hook.
Engage the clamp to install the connector as shown in the illustration.
Engage the fastener to secure the front seat airbag assembly wire harness.
71861
14.INSTALL FRONT SEAT INNER CUSHION SHIELD
Engage the 5 claws and 7 guides to install the front seat inner cushion shield.
71811D
15.INSTALL FRONT SEAT CUSHION SHIELD
Engage the 5 claws, 7 guides and clip to install the front seat cushion shield.
Install the screw.
71074S
16.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
72526A
17.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the claw to install the reclining adjuster release handle.
71849
18.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
73240
19.INSTALL FRONT SEAT INNER BELT ASSEMBLY