Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM2040EQ _58 Vehicle Interior _014729 SEAT BELT _0075100 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly.

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

B287218E14
0.615,2.448 2.823,2.625 2.208,0.177 10 false : CAN Communication Line 0.865,0.844 1.25,1.156 0.385,0.313 10 false CAN 3.438,1.25 4.552,1.896 1.115,0.646 10 false Instrument Panel Junction Block Assembly 2.073,0.844 2.583,1.083 0.51,0.24 10 false CAN 1.635,1.427 2.135,1.833 0.5,0.406 10 false MB 4.177,0.813 4.479,1.073 0.302,0.26 10 false 3A 5.146,1.177 6.5,1.677 1.354,0.5 10 false Front Seat Inner Belt Assembly RH 5.135,1.021 5.656,1.292 0.521,0.271 10 false O3 3.115,0.729 3.406,0.938 0.292,0.208 10 false 18 4.188,0.635 4.49,0.813 0.302,0.177 10 false 38 5.271,0.729 5.563,0.927 0.292,0.198 10 false 3 6.083,0.729 6.313,0.906 0.229,0.177 10 false 2 2.667,0.833 3.198,1.24 0.531,0.406 10 false DBKL 0.104,1.583 1.302,2.073 1.198,0.49 10 false Combination Meter Assembly 1.635,1.583 3.333,2.198 1.698,0.615 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch ON or OFF ON: Driver seat belt fastened
OFF: Driver seat belt unfastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14

OK:

ON or OFF appears on the tester screen according to the driver seat belt condition.


Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Driver Side Seat Belt Seat belt warning light OFF/ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Driver Side Seat Belt
50004 122 12
OK:

The seat belt warning light on the combination meter assembly operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
a.
B271232C16
0.205,0.166 0.357,0.304 0.152,0.137 10 *a
*a Component without harness connected
(Front Seat Inner Belt Assembly RH)


Remove the front seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 Driver seat belt unfastened Below 1 Ω
2 - 3 Driver seat belt fastened 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B311416C02
1.26,0.281 1.594,0.5 0.333,0.219 4.781,0.396 5.115,0.615 0.333,0.219 5.25,1.385 5.115,1.385 5.115,1.385 5.115,0.99 false 1.354,0.302 1.667,0.5 0.313,0.198 10 false 3A 4.854,0.417 5.167,0.615 0.313,0.198 10 false MB 0.24,0.146 0.552,0.344 0.313,0.198 10 false *a 5.313,1.302 5.927,1.5 0.615,0.198 10 false DBKL
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3A instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-18 (DBKL) - 3A-38 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY RH - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-38 - O3-3 Always Below 1 Ω
O3-3 - Body ground Always 10 kΩ or higher
O3-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR