Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2040EQ _59 Vehicle Exterior _014733 WINDOW / GLASS _0075142 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the power switch is on (IG), the power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

WIRING DIAGRAM

B281016
0.271,2.292 2.281,2.708 2.01,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,3.365 2.615,3.521 1.646,0.156 10 false : LIN Communication Line 0.396,0.531 1.26,1.01 0.865,0.479 10 false from Auxiliary Battery 1.688,0.667 2.552,0.896 0.865,0.229 10 false DOOR NO. 2 2.521,2.406 4.479,2.948 1.958,0.542 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.406 6.844,2.771 1.615,0.365 10 false Power Window Regulator Master Switch Assembly 2.521,2.25 2.875,2.458 0.354,0.208 10 false J9 5.229,2.26 5.708,2.542 0.479,0.281 10 false J10 1.635,1.594 2.01,1.75 0.375,0.156 10 false LIN2 2.833,1.448 3.094,1.604 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.802,0.427 4.208,0.583 0.406,0.156 10 false AUTO 5.375,0.521 5.656,0.75 0.281,0.229 10 false A 5.375,1.031 5.542,1.229 0.167,0.198 10 false D 5.375,1.531 5.542,1.729 0.167,0.198 10 false U 5.375,1.833 5.542,2.021 0.167,0.188 10 false E 3.729,0.927 4.24,1.083 0.51,0.156 10 false DWN1 3.906,1.448 4.281,1.667 0.375,0.219 10 false UP1 4.042,1.729 4.406,1.885 0.365,0.156 10 false E 4.25,1.729 4.375,1.885 0.125,0.156 10 false 1 4.25,0.938 4.375,1.094 0.125,0.156 10 false 7 5.188,0.927 5.792,1.156 0.604,0.229 10 false 5 5.198,1.438 5.875,1.656 0.677,0.219 10 false 1 5.198,1.729 5.75,1.917 0.552,0.188 10 false 9 4.25,0.427 4.375,0.583 0.125,0.156 10 false 4 5.198,0.438 5.854,0.688 0.656,0.25 10 false 4 4.25,1.448 4.438,1.604 0.188,0.156 10 false 10 2.646,0.427 2.771,0.583 0.125,0.156 10 false 2 2.635,1.448 2.813,1.604 0.177,0.156 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See pageVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When the ECU determines that the power window regulator motor assembly (for driver door) has a malfunction, DTC B2311 is stored.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MAIN BODY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Communication D-Door Motor Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) OK or STOP OK: Normal communication
STOP: Communication stopped
-
Body Electrical > Main Body > Data List
Tester Display
Communication D-Door Motor
50003 123 49
OK:

On the intelligent tester screen, OK is displayed.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)

NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)

2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Data List.


b.

Read the Data List according to the display on the intelligent tester.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Active Test.


b.

Perform the Active Test according to the display on the intelligent tester.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


Body Electrical > D-Door Motor > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -
Body Electrical > D-Door Motor > Active Test
Tester Display
Power Window
50004 124 1
OK:

Driver door power window operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the power window regulator motor assembly (for driver door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J9-2 (B) - Body ground Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
J9-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)
a.

Disconnect the power window regulator master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-1 (U) - J9-10 (UP1) Always Below 1 Ω
J10-5 (D) - J9-7 (DWN1) Always Below 1 Ω
J10-1 (U) - Body ground Always 10 kΩ or higher
J10-5 (D) - Body ground Always 10 kΩ or higher
J10-9 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B164359
2.354,1.771 2.635,2.688 false 1.677,1.792 1.458,2.698 false 1.135,1.771 0.917,2.688 false 0.188,0.188 0.479,0.406 0.292,0.219 10 false *a 0.854,2.698 0.99,2.885 0.135,0.188 10 false E 1.406,2.698 1.542,2.885 0.135,0.188 10 false D 2.615,2.698 2.75,2.885 0.135,0.188 10 false U
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (U) - 9 (E) Manual UP Below 1 Ω
5 (D) - 9 (E) Manual DOWN Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY