Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2040EQ _59 Vehicle Exterior _014733 WINDOW / GLASS _0075142 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

This DTC is stored when the ECU built into the regulator motor determines that the power window regulator master switch assembly is stuck.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2312 Power Window Switch Malfunction
·

Power window regulator master switch assembly (for driver door) stuck

·

Power window regulator master switch assembly held in same position for more than 20 seconds


·

Power window regulator master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector



WIRING DIAGRAM

B281016
0.271,2.292 2.281,2.708 2.01,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,3.365 2.615,3.521 1.646,0.156 10 false : LIN Communication Line 0.396,0.531 1.26,1.01 0.865,0.479 10 false from Auxiliary Battery 1.688,0.667 2.552,0.896 0.865,0.229 10 false DOOR NO. 2 2.521,2.406 4.479,2.948 1.958,0.542 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.406 6.844,2.771 1.615,0.365 10 false Power Window Regulator Master Switch Assembly 2.521,2.25 2.875,2.458 0.354,0.208 10 false J9 5.229,2.26 5.708,2.542 0.479,0.281 10 false J10 1.635,1.594 2.01,1.75 0.375,0.156 10 false LIN2 2.833,1.448 3.094,1.604 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.802,0.427 4.208,0.583 0.406,0.156 10 false AUTO 5.375,0.521 5.656,0.75 0.281,0.229 10 false A 5.375,1.031 5.542,1.229 0.167,0.198 10 false D 5.375,1.531 5.542,1.729 0.167,0.198 10 false U 5.375,1.833 5.542,2.021 0.167,0.188 10 false E 3.729,0.927 4.24,1.083 0.51,0.156 10 false DWN1 3.906,1.448 4.281,1.667 0.375,0.219 10 false UP1 4.042,1.729 4.406,1.885 0.365,0.156 10 false E 4.25,1.729 4.375,1.885 0.125,0.156 10 false 1 4.25,0.938 4.375,1.094 0.125,0.156 10 false 7 5.188,0.927 5.792,1.156 0.604,0.229 10 false 5 5.198,1.438 5.875,1.656 0.677,0.219 10 false 1 5.198,1.729 5.75,1.917 0.552,0.188 10 false 9 4.25,0.427 4.375,0.583 0.125,0.156 10 false 4 5.198,0.438 5.854,0.688 0.656,0.25 10 false 4 4.25,1.448 4.438,1.604 0.188,0.156 10 false 10 2.646,0.427 2.771,0.583 0.125,0.156 10 false 2 2.635,1.448 2.813,1.604 0.177,0.156 10 false 9


CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 can be stored in the power window regulator motor assembly (for driver door).

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTC.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Clear DTCs
50002 124

b.

Check for DTCs.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > D-Door Motor > Trouble Codes
50001 124
OK:

DTC B2312 is not output.



Result:
Proceed to
OK
NG



OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

NG

2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver door power window auto switch signal ON or OFF ON: Driver door power window auto switch operated
OFF: Driver door power window auto switch not operated
-
D Door P/W Up SW Driver door power window manual up switch signal ON or OFF ON: Driver door power window manual up switch operated
OFF: Driver door power window manual up switch not operated
-
D Door P/W Down SW Driver door power window manual down switch signal ON or OFF ON: Driver door power window manual down switch operated
OFF: Driver door power window manual down switch not operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Auto SW
D Door P/W Up SW
D Door P/W Down SW
50003 124 1,2,3
OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
a.

Disconnect the power window regulator master switch assembly connector.


b.

Disconnect the power window regulator motor assembly (for driver door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-1 (U) - Body ground Always 10 kΩ or higher
J10-5 (D) - Body ground Always 10 kΩ or higher
J10-4 (A) - Body ground Always 10 kΩ or higher
J9-10 (UP1) - Body ground Always 10 kΩ or higher
J9-7 (DWN1) - Body ground Always 10 kΩ or higher
J9-4 (AUTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B298969
1.677,1.781 1.188,2.771 true 1.896,1.771 2.198,2.802 true 2.365,1.781 2.854,2.708 true 0.615,2.76 1.042,1.781 true 0.083,0.052 0.396,0.281 0.313,0.229 10 false *a 1.135,2.802 1.583,2.99 0.448,0.188 10 false D 2.198,2.865 2.896,3.115 0.698,0.25 10 false A 0.531,2.76 0.729,2.938 0.198,0.177 10 false E 2.865,2.76 3.302,2.969 0.438,0.208 10 false U
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (U) - 9 (E) Released 10 kΩ or higher
1 (U) - 4 (A) Released 10 kΩ or higher
4 (A) - 9 (E) Released 10 kΩ or higher
5 (D) - 9 (E) Released 10 kΩ or higher
4 (A) - 5 (D) Released 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY