Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2040EQ _59 Vehicle Exterior _014738 LIGHTING (EXT) _0075173 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E233268E12
1.323,2.385 2.604,2.625 1.281,0.24 10 false Parking Light LH 1.323,1.688 2.51,1.948 1.188,0.26 10 false Parking Light RH 0.292,3.042 2.719,3.302 2.427,0.26 10 false Taillights and License Plate Lights 3.406,1.5 3.635,1.76 0.229,0.26 10 false 7 3.365,2.375 3.583,2.552 0.219,0.177 10 false 3D 3.375,1.698 3.708,1.917 0.333,0.219 10 false 3D 3.365,3.063 3.563,3.24 0.198,0.177 10 false 3C 3.406,2.865 3.615,3.104 0.208,0.24 10 false 5 3.406,2.188 3.635,2.417 0.229,0.229 10 false 8 0.333,0.406 1.219,0.771 0.885,0.365 10 false from Auxiliary Battery 2.167,0.625 2.74,0.896 0.573,0.271 10 false DC/DC 3.375,0.469 3.656,0.719 0.281,0.25 10 false 3F 3.406,0.281 3.615,0.552 0.208,0.271 10 false 1 4.604,1.146 5.063,1.427 0.458,0.281 10 false TAIL 5.354,1.01 5.833,1.26 0.479,0.25 10 false TAIL 6.365,0.469 6.781,0.646 0.417,0.177 10 false TRLY 6.125,0.375 6.406,0.594 0.281,0.219 10 false 14 5.427,3.906 7.073,4.24 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 5.427,3.75 5.927,4.052 0.5,0.302 10 false MB 3.333,3.5 4.99,3.896 1.656,0.396 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Check that the relay operates.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Taillight Relay Taillight relay ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Taillight Relay
50004 123 13
OK:

Taillight relay operates. (Taillights illuminate.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.
E191586C03
1.552,0.177 1.885,0.406 0.333,0.229 0.156,0.156 0.531,0.458 0.375,0.302 10 false *a 1.656,0.208 1.938,0.49 0.281,0.281 10 false 3F
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the 3F instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

E220274C06
3.396,2.125 3.771,2.354 0.375,0.229 2.865,0.188 3.24,0.417 0.375,0.229 0.792,0.375 1.167,0.604 0.375,0.229 5.625,0.188 6,0.417 0.375,0.229 3.302,2.875 3.302,3.271 false 0.146,0.125 0.302,0.281 0.156,0.156 10 false *a 3.115,3.281 3.49,3.438 0.375,0.156 10 false TRLY 3.49,2.167 3.76,2.323 0.271,0.156 10 false MB 2.969,0.229 3.188,0.385 0.219,0.156 10 false 3D 0.917,0.406 1.219,0.604 0.302,0.198 10 false 3F 5.729,0.229 5.948,0.385 0.219,0.156 10 false 3C
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Connect a positive (+) lead from the auxiliary battery to terminal 3F-1.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3D-7 - Auxiliary battery negative terminal Always 11 to 14 V
3D-8 - Auxiliary battery negative terminal Always 11 to 14 V
3C-5 - Auxiliary battery negative terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY