Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING › 2012.02–2015.04
RM2040EQ _59 Vehicle Exterior _014740 EXTERIOR PANELS / TRIM _0075194 REAR DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR BELT MOULDING  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284D 4.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 74260 6.REMOVE REAR ARMREST ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 67604 7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68174A 8.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 67842E 9.REMOVE REAR DOOR SERVICE HOLE COVER

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68640A 10.REMOVE REAR DOOR CHECK ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 67872 11.REMOVE REAR DOOR WEATHERSTRIP

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68152C 12.REMOVE REAR DOOR GLASS RUN

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 67408F 13.REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68124B 14.REMOVE REAR DOOR QUARTER WINDOW GLASS

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68104 15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 75740 16.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

a.
B280063C10
2.156,1.469 1.708,1.198 false 2.219,1.448 2.49,1.708 0.271,0.26 10 *1
*1 Protective Tape


Put protective tape around the rear door belt moulding assembly.


b.
B280064C08
2.01,0.823 1.854,0.792 false 2.052,0.75 2.365,0.99 0.313,0.24 10 false *1
*1 Protective Tape


Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.