Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING › 2012.02–2015.04
RM2040EQ _59 Vehicle Exterior _014740 EXTERIOR PANELS / TRIM _0075197 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  INSTALLATION  


PROCEDURE

Hide 75764A 1.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

a.
B280097

Engage the guide of the rear door upper window frame moulding to the door frame.


b.

Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 6 new rivets.

HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.


NOTICE:
·
B125583C14
1.323,0.271 1.469,0.271 1.469,0.271 1.813,0.708 false 1.854,1.292 1.854,1.813 false 2.365,0.031 2.563,0.188 0.198,0.156 10 false *a 1.167,0.156 1.354,0.313 0.188,0.156 10 false *1 1.771,1.813 1.948,1.969 0.177,0.156 10 false *2
*1 Riveter
*2 Mandrel
*a Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C13
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 2.323,0.083 2.5,0.24 0.177,0.156 10 false *a 2.333,1.094 2.521,1.25 0.188,0.156 10 false *a 1.458,0.354 1.948,0.51 0.49,0.156 10 false *1 1.479,1.333 1.969,1.49 0.49,0.156 10 false *1
*1 Riveter
*a Incorrect


Confirm that the rivets are seated properly against the moulding. Do not tilt the riveter when installing the rivet to the moulding. Do not leave any space between the rivet head and moulding.

·
B125585C12
1.156,0.75 1.417,0.75 false 2.448,0.313 2.76,0.615 0.313,0.302 10 false *a 1.438,0.677 1.917,1.01 0.479,0.333 10 false *1
*1 Riveter
*a Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




Hide 75762A 2.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

When installing a new rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door front window frame moulding excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B280094C06
1.458,2.573 1.5,3.052 1.5,3.052 1.615,2.573 false 2.031,1.865 1.76,2 false 1.427,0.927 1.729,1.115 false 1.271,0.833 1.583,1.094 0.313,0.26 10 false *1 2.042,1.781 2.396,2.063 0.354,0.281 10 false *1 1.406,3.052 1.708,3.313 0.302,0.26 10 false *2
*1 Double-sided Tape
*2 Caulking Sponge


Install a new rear door front window frame moulding.

i.

Using a heat light, heat the vehicle body and rear door front window frame moulding.


ii.

Remove the release paper from the rear door front window frame moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.

Install the rear door front window frame moulding with the clip.



Hide 75740 3.INSTALL REAR DOOR BELT MOULDING ASSEMBLY