Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 2 Sensor Type) › 2012.02–2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0076658 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 2 Sensor Type) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 2 Sensor Type)  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

The back sonar or clearance sonar switch assembly is installed at the base of the driver side of the instrument panel.

When the back sonar or clearance sonar switch assembly is turned on, an on signal is sent to the clearance warning ECU assembly. The Toyota parking assist-sensor system operates according to this signal.

WIRING DIAGRAM

E236270E09
3.448,1.448 5.333,2.281 1.885,0.833 10 false Back Sonar or Clearance Sonar Switch Assembly (Clearance Sonar Main Switch) 5.75,2.563 6.948,3.26 1.198,0.698 10 false Clearance Warning ECU Assembly 5.771,1.927 6,2.156 0.229,0.229 10 false 30 5.823,0.781 5.969,0.969 0.146,0.188 10 false 1 3.729,0.781 3.969,1.052 0.24,0.271 10 false 9 4.948,0.771 5.208,1.125 0.26,0.354 10 false 6 4.604,0.771 4.927,1 0.323,0.229 10 false ECU 5.99,2.042 6.167,2.24 0.177,0.198 10 false E 3.917,0.781 4.094,0.979 0.177,0.198 10 false IG 5.99,0.885 6.24,1.146 0.25,0.26 10 false IG 2.271,1.167 3.292,1.458 1.021,0.292 10 false ECU-IG1 NO. 2 0.354,0.865 1.74,1.333 1.385,0.469 10 false from IG1 NO. 2 Relay 3.427,1.271 4.281,1.5 0.854,0.229 10 false I6 5.76,2.396 6.063,2.635 0.302,0.24 10 false I82

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL


b.
E197324C01
1.563,1.396 1.563,1.635 1.563,1.635 1.052,1.635 false 2,1.396 2,1.635 2,1.635 2.51,1.635 false 0.833,1.563 1.104,1.792 0.271,0.229 10 IG 2.573,1.563 3,1.833 0.427,0.271 10 ECU 0.115,0.063 0.5,0.333 0.385,0.271 10 *a
*a Component without harness connected
(Back Sonar or Clearance Sonar Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (IG) - 6 (ECU) Clearance sonar main switch on Below 1 Ω
9 (IG) - 6 (ECU) Clearance sonar main switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY POWER SOURCE)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I6-9 (IG) - Body ground Power switch on (IG) 11 to 14 V
I6-9 (IG) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the I82 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I82-1 (IG) - I6-6 (ECU) Always Below 1 Ω
I82-1 (IG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I82-30 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR