Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM2040EQ _58 Vehicle Interior _014727 SUPPLEMENTAL RESTRAINT SYSTEMS _0075078 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost communication with Side Airbag Sensor RH  B1623/81  Side Airbag Sensor Assembly RH Initialization Incomplete  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

The side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1622/81 Lost communication with Side Airbag Sensor RH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 floor wire

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 floor wire

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1632/81 Lost Communication with Rear Airbag Sensor RH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 floor wire

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 floor wire

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1642/81 Lost Communication with Side Satellite Sensor Bus RH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

No. 2 floor wire

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C239250E32
0.552,4.698 1.365,5.135 0.813,0.438 10 O11 0.552,4.875 1.844,5.5 1.292,0.625 10 Side Airbag Sensor Assembly RH 3.042,4.875 4.427,5.438 1.385,0.563 10 Side No. 2 Airbag Sensor Assembly RH 3.042,4.698 3.667,5.042 0.625,0.344 10 O13 5.521,4.875 7.094,5.365 1.573,0.49 10 Airbag Sensor Assembly 5.521,4.698 5.896,5.156 0.375,0.458 10 O7 1.125,0.896 1.813,1.354 0.688,0.458 10 BBR+ 1.583,0.792 2.083,1.542 0.5,0.75 10 4 1.156,1.792 1.865,2.344 0.708,0.552 10 BBR- 5.563,0.896 6.104,1.385 0.542,0.49 10 BBR+ 5.333,0.792 5.76,1.333 0.427,0.542 10 17 5.333,1.698 5.813,2.427 0.479,0.729 10 18 5.563,1.792 6.083,2.354 0.521,0.563 10 BBR- 1.583,1.698 2.208,2.531 0.625,0.833 10 3 1.125,3.042 1.688,3.438 0.563,0.396 10 BCR+ 1.583,2.948 1.99,3.542 0.406,0.594 10 1 2.927,3.833 3.208,4.406 0.281,0.573 10 1 1.146,3.938 1.802,4.323 0.656,0.385 10 BCR- 3.073,3.042 3.698,3.698 0.625,0.656 10 BCR+ 3.073,3.938 3.708,4.583 0.635,0.646 10 BCR- 1.583,3.833 2.073,4.542 0.49,0.708 10 2 2.927,2.948 3.177,3.406 0.25,0.458 10 2

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then on (IG) again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642 and 81 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1642 or 81 is output. A
Current DTC B1623 is output. B
Current DTC B1632 or B1633 is output. C
Current DTC B1622 is output. D
Current DTCs B1622, B1623, B1632, B1633, B1642 and 81 are not output. E



A

2.CHECK CONNECTORS

B

13.CHECK HISTORY DTC

C

21.CHECK CONNECTORS

D

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

E

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
C238391C01
0.958,0.469 1.313,0.719 0.354,0.25 0.406,3.542 0.781,3.781 0.375,0.24 1.573,3.688 1.948,4.125 false 1.448,3.677 1.063,4.115 false 1.573,2.427 1.573,1.865 1.573,1.865 1.417,1.865 false 1.635,0.792 1.271,1.052 false 1.76,0.792 2.125,1.052 false 1.708,1.094 1.708,1.271 false 1.052,2.417 1.51,2.76 0.458,0.344 10 D 1.365,2.417 1.677,2.75 0.313,0.333 10 C 1.708,2.417 2,2.729 0.292,0.313 10 B 2.01,2.417 2.302,2.781 0.292,0.365 10 A 0.688,2.417 1.156,2.75 0.469,0.333 10 *1 2.5,2.135 2.771,2.479 0.271,0.344 10 *2 0.635,0.188 0.906,0.438 0.271,0.25 10 *a 0.354,3.198 0.74,3.531 0.385,0.333 10 *b 2.01,1.063 2.51,1.302 0.5,0.24 10 BBR- 1.094,1.063 1.563,1.281 0.469,0.219 10 BBR+ 1.063,0.51 1.375,0.781 0.313,0.271 10 O7 0.469,3.583 0.958,3.865 0.49,0.281 10 O11 1.823,4.125 2.354,4.354 0.531,0.229 10 BBR+ 0.896,4.125 1.406,4.354 0.51,0.229 10 BBR- 1.25,1.792 1.781,2.156 0.531,0.365 10 *3 1.635,1.292 1.865,1.531 0.229,0.24 10 *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - O11-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
C238220C05
0.396,2.26 0.771,2.51 0.375,0.25 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 D 1.271,0.948 1.677,1.417 0.406,0.469 10 C 1.729,0.948 2.083,1.375 0.354,0.427 10 B 2.031,0.958 2.427,1.438 0.396,0.479 10 A 0.646,0.958 0.938,1.313 0.292,0.354 10 *1 2.448,0.688 2.833,1.073 0.385,0.385 10 *2 1.146,0.281 1.51,0.656 0.365,0.375 10 *3 0.333,1.75 0.667,2.115 0.333,0.365 10 *a 0.458,2.302 0.917,2.625 0.458,0.323 10 O11 1.083,2.844 1.698,3.177 0.615,0.333 10 BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - O11-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
C238220C05
0.396,2.26 0.771,2.51 0.375,0.25 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 D 1.271,0.948 1.677,1.417 0.406,0.469 10 C 1.729,0.948 2.083,1.375 0.354,0.427 10 B 2.031,0.958 2.427,1.438 0.396,0.479 10 A 0.646,0.958 0.938,1.313 0.292,0.354 10 *1 2.448,0.688 2.833,1.073 0.385,0.385 10 *2 1.146,0.281 1.51,0.656 0.365,0.375 10 *3 0.333,1.75 0.667,2.115 0.333,0.365 10 *a 0.458,2.302 0.917,2.625 0.458,0.323 10 O11 1.083,2.844 1.698,3.177 0.615,0.333 10 BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
O11-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

6.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
C238220C05
0.396,2.26 0.771,2.51 0.375,0.25 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 D 1.271,0.948 1.677,1.417 0.406,0.469 10 C 1.729,0.948 2.083,1.375 0.354,0.427 10 B 2.031,0.958 2.427,1.438 0.396,0.479 10 A 0.646,0.958 0.938,1.313 0.292,0.354 10 *1 2.448,0.688 2.833,1.073 0.385,0.385 10 *2 1.146,0.281 1.51,0.656 0.365,0.375 10 *3 0.333,1.75 0.667,2.115 0.333,0.365 10 *a 0.458,2.302 0.917,2.625 0.458,0.323 10 O11 1.083,2.844 1.698,3.177 0.615,0.333 10 BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - Body ground Always 1 MΩ or higher
O11-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

7.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
C240589C01
0.677,3.583 0.969,3.802 0.292,0.219 0.958,0.531 1.271,0.75 0.313,0.219 1.448,3.719 1.073,4.073 false 1.635,3.719 2.01,4.073 false 1.823,0.677 1.563,1.021 false 1.938,0.667 2.198,1.01 false 1.542,4.135 1.542,4.313 false 1.688,2.281 1.688,1.76 1.688,1.76 1.469,1.76 false 1.052,2.26 1.271,2.542 0.219,0.281 10 D 1.365,2.26 1.625,2.542 0.26,0.281 10 C 1.948,2.26 2.146,2.521 0.198,0.26 10 B 2.26,2.26 2.458,2.469 0.198,0.208 10 A 0.677,2.26 0.969,2.531 0.292,0.271 10 *1 2.583,2.26 2.823,2.521 0.24,0.26 10 *2 0.896,4.094 1.344,4.333 0.448,0.24 10 BCR- 1.885,4.094 2.438,4.375 0.552,0.281 10 BCR+ 0.698,3.615 1.083,3.875 0.385,0.26 10 O13 1,0.563 1.333,0.823 0.333,0.26 10 O11 2.073,1.031 2.521,1.24 0.448,0.208 10 BCR- 1.375,1.031 1.865,1.229 0.49,0.198 10 BCR+ 1.313,1.688 1.656,1.948 0.344,0.26 10 *3 0.74,0.167 0.99,0.438 0.25,0.271 10 *a 0.448,3.26 0.75,3.51 0.302,0.25 10 *b 1.469,4.333 1.75,4.521 0.281,0.188 10 *4
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - O11-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

8.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
C238222C08
1.156,2.302 1.552,2.542 0.396,0.24 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 D 1.458,0.74 1.792,1.208 0.333,0.469 10 C 1.906,0.74 2.25,1.177 0.344,0.438 10 B 2.219,0.74 2.49,1.125 0.271,0.385 10 A 0.813,0.74 1.427,1.208 0.615,0.469 10 *1 2.469,0.74 2.75,1.073 0.281,0.333 10 *2 1.396,0.135 1.823,0.542 0.427,0.406 10 *3 0.99,1.875 1.323,2.229 0.333,0.354 10 *a 1.229,2.344 1.625,2.688 0.396,0.344 10 O11 2.344,2.854 2.917,3.073 0.573,0.219 10 BCR- 1.646,2.865 2.135,3.188 0.49,0.323 10 BCR+
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - O11-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
C238222C08
1.156,2.302 1.552,2.542 0.396,0.24 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 D 1.458,0.74 1.792,1.208 0.333,0.469 10 C 1.906,0.74 2.25,1.177 0.344,0.438 10 B 2.219,0.74 2.49,1.125 0.271,0.385 10 A 0.813,0.74 1.427,1.208 0.615,0.469 10 *1 2.469,0.74 2.75,1.073 0.281,0.333 10 *2 1.396,0.135 1.823,0.542 0.427,0.406 10 *3 0.99,1.875 1.323,2.229 0.333,0.354 10 *a 1.229,2.344 1.625,2.688 0.396,0.344 10 O11 2.344,2.854 2.917,3.073 0.573,0.219 10 BCR- 1.646,2.865 2.135,3.188 0.49,0.323 10 BCR+
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
O11-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
C238222C08
1.156,2.302 1.552,2.542 0.396,0.24 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 D 1.458,0.74 1.792,1.208 0.333,0.469 10 C 1.906,0.74 2.25,1.177 0.344,0.438 10 B 2.219,0.74 2.49,1.125 0.271,0.385 10 A 0.813,0.74 1.427,1.208 0.615,0.469 10 *1 2.469,0.74 2.75,1.073 0.281,0.333 10 *2 1.396,0.135 1.823,0.542 0.427,0.406 10 *3 0.99,1.875 1.323,2.229 0.333,0.354 10 *a 1.229,2.344 1.625,2.688 0.396,0.344 10 O11 2.344,2.854 2.917,3.073 0.573,0.219 10 BCR- 1.646,2.865 2.135,3.188 0.49,0.323 10 BCR+
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - Body ground Always 1 MΩ or higher
O11-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE NO. 2 FLOOR WIRE

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642 or 81 is output. A
DTC B1647 or 82 is output. B
DTCs B1642, B1647, 81 and 82 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

12.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1642, B1647, 81 and 82 are not output. A
DTC B1642 or 81 is output. B
DTC B1647 or 82 is output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

13.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1622 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1622 is not output. A
History DTC B1622 is output. B



A

14.CHECK CONNECTORS

B

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
14.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

15.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

15.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
C238391C01
0.958,0.469 1.313,0.719 0.354,0.25 0.406,3.542 0.781,3.781 0.375,0.24 1.573,3.688 1.948,4.125 false 1.448,3.677 1.063,4.115 false 1.573,2.427 1.573,1.865 1.573,1.865 1.417,1.865 false 1.635,0.792 1.271,1.052 false 1.76,0.792 2.125,1.052 false 1.708,1.094 1.708,1.271 false 1.052,2.417 1.51,2.76 0.458,0.344 10 D 1.365,2.417 1.677,2.75 0.313,0.333 10 C 1.708,2.417 2,2.729 0.292,0.313 10 B 2.01,2.417 2.302,2.781 0.292,0.365 10 A 0.688,2.417 1.156,2.75 0.469,0.333 10 *1 2.5,2.135 2.771,2.479 0.271,0.344 10 *2 0.635,0.188 0.906,0.438 0.271,0.25 10 *a 0.354,3.198 0.74,3.531 0.385,0.333 10 *b 2.01,1.063 2.51,1.302 0.5,0.24 10 BBR- 1.094,1.063 1.563,1.281 0.469,0.219 10 BBR+ 1.063,0.51 1.375,0.781 0.313,0.271 10 O7 0.469,3.583 0.958,3.865 0.49,0.281 10 O11 1.823,4.125 2.354,4.354 0.531,0.229 10 BBR+ 0.896,4.125 1.406,4.354 0.51,0.229 10 BBR- 1.25,1.792 1.781,2.156 0.531,0.365 10 *3 1.635,1.292 1.865,1.531 0.229,0.24 10 *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - O11-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

16.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

16.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
C238220C05
0.396,2.26 0.771,2.51 0.375,0.25 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 D 1.271,0.948 1.677,1.417 0.406,0.469 10 C 1.729,0.948 2.083,1.375 0.354,0.427 10 B 2.031,0.958 2.427,1.438 0.396,0.479 10 A 0.646,0.958 0.938,1.313 0.292,0.354 10 *1 2.448,0.688 2.833,1.073 0.385,0.385 10 *2 1.146,0.281 1.51,0.656 0.365,0.375 10 *3 0.333,1.75 0.667,2.115 0.333,0.365 10 *a 0.458,2.302 0.917,2.625 0.458,0.323 10 O11 1.083,2.844 1.698,3.177 0.615,0.333 10 BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - O11-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

17.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
C238220C05
0.396,2.26 0.771,2.51 0.375,0.25 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 D 1.271,0.948 1.677,1.417 0.406,0.469 10 C 1.729,0.948 2.083,1.375 0.354,0.427 10 B 2.031,0.958 2.427,1.438 0.396,0.479 10 A 0.646,0.958 0.938,1.313 0.292,0.354 10 *1 2.448,0.688 2.833,1.073 0.385,0.385 10 *2 1.146,0.281 1.51,0.656 0.365,0.375 10 *3 0.333,1.75 0.667,2.115 0.333,0.365 10 *a 0.458,2.302 0.917,2.625 0.458,0.323 10 O11 1.083,2.844 1.698,3.177 0.615,0.333 10 BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
O11-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

18.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

18.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
C238220C05
0.396,2.26 0.771,2.51 0.375,0.25 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 D 1.271,0.948 1.677,1.417 0.406,0.469 10 C 1.729,0.948 2.083,1.375 0.354,0.427 10 B 2.031,0.958 2.427,1.438 0.396,0.479 10 A 0.646,0.958 0.938,1.313 0.292,0.354 10 *1 2.448,0.688 2.833,1.073 0.385,0.385 10 *2 1.146,0.281 1.51,0.656 0.365,0.375 10 *3 0.333,1.75 0.667,2.115 0.333,0.365 10 *a 0.458,2.302 0.917,2.625 0.458,0.323 10 O11 1.083,2.844 1.698,3.177 0.615,0.333 10 BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-4 (BBR+) - Body ground Always 1 MΩ or higher
O11-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE NO. 2 FLOOR WIRE

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1623 and B1628 are not output. A
DTC B1623 is output. B
DTC B1628 is output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1622 is output. B
DTC B1627 is output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

21.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

22.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

22.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
C240589C01
0.677,3.583 0.969,3.802 0.292,0.219 0.958,0.531 1.271,0.75 0.313,0.219 1.448,3.719 1.073,4.073 false 1.635,3.719 2.01,4.073 false 1.823,0.677 1.563,1.021 false 1.938,0.667 2.198,1.01 false 1.542,4.135 1.542,4.313 false 1.688,2.281 1.688,1.76 1.688,1.76 1.469,1.76 false 1.052,2.26 1.271,2.542 0.219,0.281 10 D 1.365,2.26 1.625,2.542 0.26,0.281 10 C 1.948,2.26 2.146,2.521 0.198,0.26 10 B 2.26,2.26 2.458,2.469 0.198,0.208 10 A 0.677,2.26 0.969,2.531 0.292,0.271 10 *1 2.583,2.26 2.823,2.521 0.24,0.26 10 *2 0.896,4.094 1.344,4.333 0.448,0.24 10 BCR- 1.885,4.094 2.438,4.375 0.552,0.281 10 BCR+ 0.698,3.615 1.083,3.875 0.385,0.26 10 O13 1,0.563 1.333,0.823 0.333,0.26 10 O11 2.073,1.031 2.521,1.24 0.448,0.208 10 BCR- 1.375,1.031 1.865,1.229 0.49,0.198 10 BCR+ 1.313,1.688 1.656,1.948 0.344,0.26 10 *3 0.74,0.167 0.99,0.438 0.25,0.271 10 *a 0.448,3.26 0.75,3.51 0.302,0.25 10 *b 1.469,4.333 1.75,4.521 0.281,0.188 10 *4
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - O11-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

23.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

23.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
C238222C08
1.156,2.302 1.552,2.542 0.396,0.24 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 D 1.458,0.74 1.792,1.208 0.333,0.469 10 C 1.906,0.74 2.25,1.177 0.344,0.438 10 B 2.219,0.74 2.49,1.125 0.271,0.385 10 A 0.813,0.74 1.427,1.208 0.615,0.469 10 *1 2.469,0.74 2.75,1.073 0.281,0.333 10 *2 1.396,0.135 1.823,0.542 0.427,0.406 10 *3 0.99,1.875 1.323,2.229 0.333,0.354 10 *a 1.229,2.344 1.625,2.688 0.396,0.344 10 O11 2.344,2.854 2.917,3.073 0.573,0.219 10 BCR- 1.646,2.865 2.135,3.188 0.49,0.323 10 BCR+
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - O11-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

24.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
C238222C08
1.156,2.302 1.552,2.542 0.396,0.24 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 D 1.458,0.74 1.792,1.208 0.333,0.469 10 C 1.906,0.74 2.25,1.177 0.344,0.438 10 B 2.219,0.74 2.49,1.125 0.271,0.385 10 A 0.813,0.74 1.427,1.208 0.615,0.469 10 *1 2.469,0.74 2.75,1.073 0.281,0.333 10 *2 1.396,0.135 1.823,0.542 0.427,0.406 10 *3 0.99,1.875 1.323,2.229 0.333,0.354 10 *a 1.229,2.344 1.625,2.688 0.396,0.344 10 O11 2.344,2.854 2.917,3.073 0.573,0.219 10 BCR- 1.646,2.865 2.135,3.188 0.49,0.323 10 BCR+
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
O11-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

25.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

25.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
C238222C08
1.156,2.302 1.552,2.542 0.396,0.24 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 D 1.458,0.74 1.792,1.208 0.333,0.469 10 C 1.906,0.74 2.25,1.177 0.344,0.438 10 B 2.219,0.74 2.49,1.125 0.271,0.385 10 A 0.813,0.74 1.427,1.208 0.615,0.469 10 *1 2.469,0.74 2.75,1.073 0.281,0.333 10 *2 1.396,0.135 1.823,0.542 0.427,0.406 10 *3 0.99,1.875 1.323,2.229 0.333,0.354 10 *a 1.229,2.344 1.625,2.688 0.396,0.344 10 O11 2.344,2.854 2.917,3.073 0.573,0.219 10 BCR- 1.646,2.865 2.135,3.188 0.49,0.323 10 BCR+
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (BCR+) - Body ground Always 1 MΩ or higher
O11-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE NO. 2 FLOOR WIRE

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connector to the side No. 2 airbag sensor assembly RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1632 or B1633 is output. A
DTC B1637 or B1638 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

27.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

27.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1632, B1633, B1637 and B1638 are not output. A
DTC B1632 or B1633 is output. B
DTC B1637 or B1638 is output. C


g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1622 is output. B
DTC B1627 is output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH